JAC HFC4180KR1K3 Owner'S Manual Download Page 16

Page: 16 / 112

INSTRUMENT CLUSTER AND INDICATOR

（

Ⅲ

）

1. Speed/odometer

2. Air pressure gauge

3. Oil pressure gauge

4. Tachometer

5. Water temperature gauge

6. Fuel gauge

OIL PRESSURE GAUGE

The gauge indicates the engine oil pressure while the engine is running.

If the gauge indicates below 0.5 kg/cm

, oil warning lamp comes on and

buzzerwill sound at the same time.

At this time stop the engine immediately and check the lubricating system.

NOTE:

Engine oil pressure when the engine is cold may go up above normal pressure.

If the engine Is warm,the gauge will Indicate normal pressure Immediately.

If the oil filter is clogged, the oil pressure warning light comes on but the buzzer

will not sound.

OWNER

’

S MANUAL

JAC HEAVY DUTY TRUCK

Summary of Contents for HFC4180KR1K3

















































































































Search results

Summary of Contents for HFC4180KR1K3

Reviews:

Related manuals for HFC4180KR1K3

Brands by name

Popular brands

JAC HFC4180KR1K3, Owner'S Manual

Search results

Summary of Contents for HFC4180KR1K3

Reviews:

Related manuals for HFC4180KR1K3

Brands by name

Popular brands