background image

4

QUATTRO LITE MANUAL

TRANSMITTER LAYOUT (CONTINUED)

3.2

TRANSMITTER SPECIFICATIONS

CONTROL STICK LENGTH ADJUSTMENT

NECK STRAP ATTACHMENT

Model Number

NET-E104  

RF

72MHz

Modulation

PPM (FM)

There is an eye hook on the front of the transmitter
for attaching an optional Neck Strap (JRPA023). The
eye hook is precisely positioned (see Section 3.2)

so that the transmitter will be perfectly balanced
when a neck strap is used.

To adjust the control stick length, use a 2mm Allen
wrench to unlock the set screw located inside the
end of the control stick. Turn the set screw
counterclockwise to loosen it, then turn the knurled
portion of the stick to adjust the length.
Counterclockwise will lengthen the stick and
clockwise will shorten it. After the control stick(s)
has been adjusted to suit your flying style, tighten
the set screw.

LOOSEN

TIGHTEN

SET SCREW

3.3

3.4

3.5

8 “AA” Alkaline 
Transmitter
Battery Case

Trainer Cord Jack

Transmitter
Frequency Crystal

Set Screw

Loosen

Tighten

Rudder

Elevator

Aileron

Throttle

Carrying Bar

Servo Reversing Switches

(Located behind Transmitter Battery Case)

Output Power 

Approximately 750mw

Current Drain

150mAh

Power Source

8 “AA” Alkaline Batteries (not included)

Output Pulse

1.0 –2.0ms

Back Cover

JRP4477.46 Update Quattro  1/29/01  4:20 PM  Page 4

Summary of Contents for Quattro Lite





















Reviews: