iWave iW-RainboW-G35D Hardware User'S Manual Download Page 33

Page: 33 / 110

REL0.2

Page 33 of 110

iWave Systems Technologies Pvt. Ltd.

Zynq Ult MPSoC (ZU11/17/19EG) SOM DevKit Hardware User Guide

2.4.5

Standard SD Port

The Zynq Ult MPSoC (ZU11/17/19EG) Carrier Board supports one SD interface through SD1 interface of Zynq

Ult MPSoC (ZU11/17/19EG) PS. This SD1 signals from Board to Board connector2 is connected to Standard SD

connector (J33) through auto-direction control memory card voltage level translator to support both 1.8V and 3.3V

supported cards. It supports up to 4-Bit data transfer with card detect and write protect.

The memory card voltage level translator

’s

voltage selection is controlled through PS GPIO (PS_MIO43_501) pin from

Board to Board Connector2 pin44. If PS_MIO43_501 is set to low, then 3.3V IO level is selected for SD1 signals to SD

connector. If PS_MIO43_501 is set to high, then 1.8V IO level is selected for SD1 signals to SD connector. The Standard

SD connector (J33) is physically located at the bottom of the board as shown below.

Figure 15: Standard SD Connector

Summary of Contents for iW-RainboW-G35D















































































































Search results

Summary of Contents for iW-RainboW-G35D

Reviews:

Related manuals for iW-RainboW-G35D

Brands by name

Popular brands

iWave iW-RainboW-G35D, Hardware User'S Manual

Search results

Summary of Contents for iW-RainboW-G35D

Reviews:

Related manuals for iW-RainboW-G35D

Brands by name

Popular brands