10
Manual instruction
EN
ATTENTION! DANGER OF ELECTRIC SHOCK!
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in
damp or wet locations. Keep work area well lit and
dry. Try to prevent the device from getting wet or
being exposed to humidity. Do not leave it outside
overnight. Water entering a power tool will increase
the risk of electric shock.
The power supply cable should be checked
•
regularly and, before using it, make sure the cable
is not damaged or worn out. If the cable is not in
good condition, do not use the appliance; take it to
an authorized service centre.
When tool is used outdoor, only use an extension
•
cable that is suitable for outdoor work and which is
marked for this specific use. Keep it away from the
working area, from damp, wet or oily surfaces and
away from heat and fuels.
Avoid any accidental starting: make sure the
•
switch is “off” before plugging it in.
Remove adjusting keys or wrenches before
•
turning the tool on.
Do not use the tool if the switch does not turn
•
ON or OFF. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
WARNING!
During the use of the tool,
some dust containing chemicals known
to cause cancer, may occur. Some of these
chemicals are: lead from lead based paints,
crystalline silica from bricks and cement and other
masonry products, arsenic and chromium from
chemically treated lumber and other dangerous
products. If dust is present, your risk from these
exposures varies, depending on how often you do
this type of work.
To reduce your exposure to these
chemicals, any time you do pulverulent operations,
work in a well ventilated area and work with
approved safety equipment, such as dust masks
that are specially designed to filter out microscopic
particles.
If the appliance strikes a foreign body, examine
•
the device for signs of damage and carry out any
necessary repairs before restarting and continuing
to work.
If the appliance starts to vibrate abnormally, turn
•
it off and check for the cause immediately. Vibration
is generally a warning of trouble.
Always switch off the appliance and wait until
•
the device completely stops whenever you leave the
machine, before carrying out maintenance, before
checking, cleaning or working on the appliance.
Wear suitable working clothes, long trousers
•
and solid shoes. Do not operate the appliance when
barefoot or wearing open sandals.
Use safety equipment!
•
It is forbidden to move or modify any of the
•
internal parts of the device.
Specific safety rules
Do not cover: fire danger exists if the equipment
•
is covered.
Do not use the machine in case of relative
•
humidity above 80%.
Keep inflammable materials at a minimum safety
•
distance of 0,5 meters.
Do not use the machine in fire hazardous areas!
•
Do not use the machine outdoors in rainy
•
weather!
The machine must only be disassembled by the
•
manufactory or by a qualified person!
The machine must not be located immediately
•
below a socket-outlet.
Do not use the machine with a programmer,
•
timer or any other device that switches the heater
on automatically, since a fire risk exists if the heater
is covered or positioned incorrectly.
Don’t use the machine in the immediate
•
surroundings of a bath, a shower or a swimming
pool.
If the supply cord is damaged, it must be
•
replaced by the manufacturer or a qualified person
in order to avoid any hazard.
The machine is to be placed on the floor.
•
The fan heater can be used in areas of both
•
moderate and cold climates with temperatures
ranging from -10°C up to +40°C excluding
conditions where the power cable may be exposed
to precipitation or humidity.
Do not use the machine for a period up to 24
•
hours; in this case overheating danger exist: switch
immediately off and let the machine cool down for
2 hours.
Unpacking
When unpacking, check to make sure that all
components are included. Refer to the drawings
on this manual. If any parts are missing or broken,
please call IVT assistance center.
Initial operation
Always use the correct supply voltage: the power
supply voltage must match the information quoted
