IVT 09LR-N Service Manual Download Page 25

Page: 25 / 64

12LRN

3 – 3

✩

1—The outdoor unit restarts four times before the indoor unit error is displayed (complete shutdown).

✩

2—A single error judgment results in the display of the indoor unit error (complete shutdown).

✩

3—The outdoor unit restarts eight times before the indoor unit error is displayed (complete shutdown).

[2] AIR TO AIR HEAT PUMP OPERATION IN THERMISTOR ERROR

1. Indoor unit

29 PAM clock error

When power source frequency can-
not be determined (at startup), or
when power source clock cannot
be detected for 1 continuous sec-
ond (at startup).

At compressor startup,
when in operation

Compressor continues
operation without stop-
ping.

None

Yes

Item

Mode

Control operation When resistance

is low (tempera-

ture judged higher

than actual)

Short-circuit

When resistance

is high (tempera-

ture judged lower

than actual)

Open-circuit

Room temperature
thermistor (TH1)

Auto

Operation mode
judgment

Cooling mode is
activated even if
room temperature
is low.

Cooling mode is
activated in most
cases.

Heating mode is
activated even if
room temperature
is high.

Heating mode is
always activated.

Cooling

Frequency control Room becomes too

cold.

Air conditioner
operates in full
power even when
set temperature is
reached.

Room does not
become cool.

Compressor does
not operate.

Dehumidifying

Room temperature
memory
Frequency control

Normal operation. Room temperature

is stored in memory
as 31.0



C, and

compressor does
not stop.

Normal operation. Room temperature

is stored in memory
as 18.5



C, and

compressor does
not operate.

Heating

Frequency control Room does not

become warm.

Hot keep status
results immedi-
ately after opera-
tion starts.
Frequency does
not increase above
30 Hz (40 Hz).

Room becomes too
warm.

Air conditioner
operates in full
power even when
set temperature is
reached.

Heat exchanger
thermistor (TH2)

Cooling
Dehumidifying

Freeze prevention Indoor unit evapo-

rator may freeze.

Indoor unit evapo-
rator may freeze.

Compressor stops
occasionally.

Compressor does
not operate.

Heating

Cold air prevention Cold air prevention

deactivates too
soon and cold air
discharges.

Compressor oper-
ates at low speed
or stops, and fre-
quency does not
increase.

Cold air prevention
deactivates too
slow.

Cold air prevention
does not deacti-
vate, and indoor
unit fan does not
rotate.

Function

Operation

Self-diagnosis result

display

Description

Detection period

Reset condition

Indoor

unit error

display

Indoor

unit

Outdoor

unit

Summary of Contents for 09LR-N

































































Search results

Summary of Contents for 09LR-N

Reviews:

Related manuals for 09LR-N

Brands by name

Popular brands

IVT 09LR-N, Service Manual

Search results

Summary of Contents for 09LR-N

Reviews:

Related manuals for 09LR-N

Brands by name

Popular brands