ITW SIMCO ION IQ Power HL Sensor Installation And Operating Instructions Manual Download Page 19

17

IQ Power HL Sensor

5201252 Rev. A

9. WARRANTY & SERVICE

This product has been carefully tested at the factory and is warranted to be free from 

any defects in materials or workmanship.  Simco-Ion will, under this warranty, repair 

or replace any equipment that proves, upon our examination, to have become defective 

within one year from the date of purchase.
The equipment being returned under warranty should be shipped by the purchaser to 

Simco-Ion, 2257 North Penn Road, Hatfield, PA 19440, transportation prepaid and insured 

for its replacement cost.  Prior to returning any goods for any reason, contact Simco-Ion 

Customer Service at (215) 822-6401 for a Return Authorization Number.  This number 

must accompany all returned items.
This warranty does not apply when the equipment has been tampered with, misused, 

improperly installed, altered, has received damage through abuse, carelessness, accident, 

connected to improper line voltage, or has been serviced anyone other than an authorized 

factory representative.
The warranty does not apply when Simco-Ion parts and equipment have been energized 

by other than the appropriate Simco-Ion power supply or generator, or when a Simco-

Ion power supply or generator has been used to energize other than Simco-Ion parts 

and equipment.  Simco-Ion makes no warranty, expressed or implied, nor accepts any 

obligation, liabilities, or responsibility in connection with the use of this product other than 

the repair or replacement of parts stated herein.
Information in this publication supersedes that in all previous published material.
Specifications are subject to change without notice.

Summary of Contents for SIMCO ION IQ Power HL Sensor





















Reviews: