ITT Goulds Pumps ICM Installation, Operation And Maintenance Manual Download Page 12 | Manualshive

Page: 12 / 40

background image

2 Technical data

2.1 Technical data

Manufacturer

ITT Goulds Pumps

Millwey Rise Industrial Estate

Axminster, Devon,

EX13 5HU

UK

Tel : +44 (0)1297-639100

Fax : +44 (0)1297-630476

Designation

Model ICM

Magnetic Chemical Process Pump, bearing lubrication: grease.

Model ICMP

Magnetic Chemical Process Pump for high pressure / high temperature applications,
with center-line mounted casing, bearing lubrication: grease.

Technical specifications to ISO 15783 and DIN ISO 5199.

Connecting dimensions to ISO 2858 / DIN EN 22858

Flange connecting dimensions :

DIN EN 1092-2, type B

(ISO 7005-2, type B) PN 16

ATEX 100a: Directive 94/9/EC

Machine Directive: 2006/42/EC

Materials

Standard ICM/ICMP:

Stainless steel (1.4408)

Optional ICM:

Ductile cast iron/ cast iron, Duplex, Hastelloy C, titanium

Optional ICMP:

Steel/cast iron, Duplex, Hastelloy C, titanium

Flow rates

up to 340 m3/h (at 2900 rpm)

Delivery heads

up to 150 mLC (at 2900 rpm)

Housing discharge pressure

ICM

16 bar (max. 25 bar with 65-40-315, 50-32-315 and 80-50-315)

ICMP

25 bar

Temperature range

-40° C to +180° C

2 Technical data

10

Model ICM/ICMP Magnetic Drive Chemical Process Pump with Grease Bearing Lubrication Installation, Operation, and

Maintenance Manual

«
...
10
11
12
13
14
...
»

Summary of Contents for Goulds Pumps ICM









































Reviews:

No comments

Related manuals for Goulds Pumps ICM

Brand: Nastec Pages: 28

Exubera Pro UC EV9333-50

Brand: Everpure Pages: 2

Brand: Noritz Pages: 120

UFLEX SilverSteer UP25 F-SVS

Brand: Ultraflex Pages: 29

Brand: Pfeiffer Vacuum Pages: 46

Brand: Pattfield Ergo Tools Pages: 162

Brand: Waterax Pages: 5

Brand: deconta Pages: 12

1 EPBH 9.2-11 T-AVS

Brand: EBARA Pages: 16

Brand: W'eau Pages: 32

Brand: Bristan Pages: 20

Brand: Pattfield Ergo Tools Pages: 154

Brand: PFT Pages: 48

Brand: OLIJU Pages: 12

Brand: Zelmer Pages: 54

Brand: Pet Mate Pages: 4

Brand: Ouellet Pages: 40

Brand: Noritz Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands