Index
PcOS Series 90PLUS
Programmer's Guide
Page 164
Rev M
12/16/99
Index
[
[CAN] Clear print buffer ........................................75
[CR] New line........................................................19
[DC2] Set 10 cpi ....................................................35
[DC4] End one-line double-wide print....................37
[ENQ] <1> Inquire Cash Drawer 1 status ...............82
[ENQ] <10> Request printer reset ..........................85
[ENQ] <11> Request printer power-cycle status .....86
[ENQ] <12> MICR read cancel ........................ 73, 86
[ENQ] <15> Inquire printer state............................87
[ENQ] <2> Inquire Cash Drawer 2 status ...............82
[ENQ] <20> Inquire all printer status .....................88
[ENQ] <3> Inquire receipt-paper low status ...........83
[ENQ] <4> Inquire receipt-paper out status ............83
[ENQ] <5> Inquire slip-stop sensor status ..............83
[ENQ] <6> Inquire form position sensor status .......83
[ENQ] <7> Inquire form clamp status.....................84
[ENQ] <8> Inquire cover open status......................84
[ENQ] <9> Send response ......................................84
[ENQ] <n> Inquire printer status............................82
[ESC] - <0> End underline.....................................39
[ESC] - <1> Begin underline ..................................39
[ESC] r <11> Rotate 270
°
, 5x7 font.......................45
[ESC] r <15> Rotate 270
°
, formatting, 5x7 font.....45
[ESC] r <3> Rotate 270
°
, 7x9 font.........................45
[ESC] r <7> Rotate 270
°
, formatting, 7x9 font.......45
[ESC] ! <n> Select International Character Set .......28
[ESC] # <0> Begin HSD mode ...............................26
[ESC] % G Begin italics.........................................41
[ESC] % H End italics............................................41
[ESC] * <m> … Print graphics in mode <m> .........50
[ESC] * <m> … Print single-density graphics ........51
[ESC] \: Set 12 cpi..................................................35
[ESC] ? <m> <n> Reassign graphic mode...............50
[ESC] [ @ ... Double-high, double-wide, and italics38
[ESC] [ C <n> Euro character enable......................33
[ESC] [ P <n> Set cpi.............................................36
[ESC] [ S... Redefine character set..........................31
[ESC] [ T <n
h
> <n
l
> Select character code page......30
[ESC] [DC1] Open form clamp...............................63
[ESC] [DC3] Close form clamp ..............................63
[ESC] [DC4] Select validation mode ......................64
[ESC] [EM] <n> Set validation delays....................66
[ESC] [EM] B <n> Bar code height ........................56
[ESC] [EM] C <0> Validation clamp delay.............66
[ESC] [EM] J <n> Set bar code justification ...........57
[ESC] [EM] J <n> Set human readable number ......57
[ESC] [EM] M <n> Set MICR start delay ...............73
[ESC] [EM] P <n> Top of slip position...................68
[ESC] [EM] U <n> Set validation delay..................67
[ESC] [EM] V <n> Set validation delay..................66
[ESC] [EM] W <n> Set eject pause ........................67
[ESC] [EM] W <n> Set eject wait ..........................67
[ESC] [SI] Set 24 cpi..............................................35
[ESC] ] Reverse line feed .......................................25
[ESC] ^ <n> Print control character........................31
[ESC] _ <0> End overscore ....................................39
[ESC] _ <1> Begin overscore .................................39
[ESC] ~ <n> Extended diagnostics .........................90
[ESC] < <n> Data pass-through..............................76
[ESC] < <n> Print suppress....................................76
[ESC] 0 Set line space 27/216 inch.........................22
[ESC] 1 Set line space 7/72 inch ............................23
[ESC] 2 Enable variable line spacing......................23
[ESC] 3 <n> Set line spacing n/216 inch ................22
[ESC] 4 Set top of form .........................................24
[ESC] 5 <0> End automatic line feed .....................25
[ESC] 5 <1> Begin automatic line feed...................25
[ESC] 8 Disable PE sensor .....................................60
[ESC] 9 Enable PE sensor ......................................60
[ESC] a <n> Set justification..................................21
[ESC] A <n> Set variable line spacing n/72 inch ....23
[ESC] b <n> ... Print bar code ................................55
[ESC] B <n
1
> <n
2
> <n
3
> … Set vertical tab stops...24
[ESC] C [NUL] Set form length in inches ...............25
[ESC] C Set form length in lines ............................25
[ESC] d <n> Enable variable line spacing...............23
[ESC] D <n
1
> <n
2
> … Set horizontal tab stops .......20
[ESC] E Begin emphasized print ............................40
[ESC] F End emphasized print ...............................40
[ESC] f Select receipt station..................................58
[ESC] g <0> Graphic-save print .............................53
[ESC] g <1> Start graphic-save record....................53
[ESC] g <2> Stop graphic-save record ....................53
[ESC] g <3> Stop and save graphic-save data .........53
[ESC] g <7> Stop/save graphic-save start-up macro 54
[ESC] G Begin enhanced print ...............................40
[ESC] H End enhanced print ..................................40
[ESC] I <1> Set print quality mode.........................26
[ESC] i Select slip mode ........................................64
[ESC] J <n> Fine line feed .....................................22
[ESC] j Select validation mode...............................64
[ESC] K <n>
1
<n>
2
Print single-density graphics ....48
[ESC] k Eject slip ..................................................65
[ESC] l <n> Dual station control ............................69
[ESC] L … Half-speed, double-density graphics .....48
[ESC] mD Request MICR data ...............................72
[ESC] mE Request MICR eject...............................72
[ESC] mI Reset MICR reader .................................70
[ESC] mL Request MICR load ...............................72
[ESC] mO Request MICR read with check in throat71
[ESC] mP Request MICR read ...............................71
[ESC] mR Request MICR read ...............................71
[ESC] mS Request MICR reader status...................71
[ESC] mT Request MICR transport ........................73
[ESC] P <0> End 90
°
rotated font...........................27
Summary of Contents for PcOS series 90plus
