ITEM 0.0.641.21 Notes On Use And Installation Download Page 11

Page: 11 / 12

Maintenance

Linear Unit KRF 8 80x40 ZR



Recommended oil: Track Oil for Linear Slides (Klüber Oil 4 UH1-460),

0.0.612.75

Auxiliary tool: Pressol oil can KLE-LR, 0.0.612.74

The felt pieces are supplied in ready-oiled condition.

Greases containing solid particles (e.g. graphite and MoS2 additives)

must

not

be used!



The maintenance openings (page 6) are located on both sides of the

preassembled carriage.

All 4 End Cap and Lubricating Systems are re-oiled through the

maintenance openings.

Minimum stroke, full lubrication: H

min

= 100 mm.

Maintenance interval: every 6 months or every 2,500 km

Fill quantity: approx. 1 ml per End Cap and Lubricating System and

maintenance interval (1 ml is equivalent to one pump actuation of the

Pressol oil can).

Summary of Contents for 0.0.641.21













Search results

Summary of Contents for 0.0.641.21

Reviews:

Related manuals for 0.0.641.21

Brands by name

Popular brands

ITEM 0.0.641.21, Notes On Use And Installation

Search results

Summary of Contents for 0.0.641.21

Reviews:

Related manuals for 0.0.641.21

Brands by name

Popular brands