ITech IT-M7700 Series Programming Manual Download Page 41

Page: 41 / 126

SYSTem Subsystem

SYSTem:RWLock

This command is transmit through interface, the same function as SYST:REM,

but the difference is: this command can lock “LOCAL” button as well. When this
command is executed, the “Local” button can’t switch to local control mode.

Syntax

SYST:RWL

Arguments

None

SYSTem:BEEPer

This command is used to turn on/turn off the beeper, when the arguments is set

to 1/ON, the beeper is enabled and press keyboard will beeper, otherwise, it is

mute.

Syntax

SYSTem:BEEPer <OFF|ON|0|1>

Arguments

<OFF|ON|0|1>

Example

SYST:BEEP 1

SYSTem:BEEPer?

This command is used to query the status of the buzzer.

Syntax

SYSTem:BEEPer?

Arguments

None

Example

SYST:BEEP?

Summary of Contents for IT-M7700 Series































































































































Search results

Summary of Contents for IT-M7700 Series

Reviews:

Related manuals for IT-M7700 Series

Brands by name

Popular brands

ITech IT-M7700 Series, Programming Manual

Search results

Summary of Contents for IT-M7700 Series

Reviews:

Related manuals for IT-M7700 Series

Brands by name

Popular brands