![background image](http://html1.mh-extra.com/html/sealey/ak623/ak623_instructions_1225890001.webp)
Ensure all workshop safety rules, regulations, and conditions are complied with when using torque wrench.
Maintain the
wrench in good condition and replace any damaged or worn parts.
Use genuine parts
only. Non-authorised parts may be dangerous and will invalidate the warranty.
The wrench is a precision tool,
DO NOT
abuse it.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
WARNING! DO NOT
use the wrench if damaged or thought to be faulty. (Contact Service Agent).
DO NOT
drop or throw the wrench.
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
DO NOT
use any cleaner which might affect the high pressure grease with which the wrench it is packed.
After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.
Heat treated steel ratchet head. Fully hardened and tempered. Chrome plated for corrosion resistance.
Calibration tolerance in accordance with BS EN ISO 6789:2003. Every wrench is tested and supplied with
an individually numbered test certificate. Micrometer type torque range adjustment with scale graduated in
both lb.ft and Nm. Flip reverse ratchet mechanism. Supplied in storage case.
Model No:
AK623 AK624
Torque Range (lb.ft/Nm):
20-80/27-108
20-150/27-204
Drive (“sq.):
3/8 1/2
Length (mm):
275 465
AK623/624 Issue: 4(L) - 08/09/16
© Jack Sealey Limited
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and
properly maintained, give years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR
FUTURE USE.
Instructions for:
TORQUE WRENCHES
Model No's:
AK623, AK624
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATIONS
3.1.
Hold torque wrench in one hand so that required scale (lb.ft or Nm)
is uppermost and visible.
3.2.
Turn knurled lock screw at end of handle anticlockwise to unlock knurled adjusting grip.
3.3.
Turn adjusting grip to select torque setting as follows:
• Required setting - 56lb.ft
•
Turn grip until top edge of grip is level with the 50lb.ft line on the handle scale and the zero graduation on
the grip is aligned with the centre line of the handle scale.
• Rotate the handle further, clockwise, until the ‘6’ graduation on the grip is aligned with the centre line to
give a setting of 50 + 6 = 56lb.ft.
Note: If using the Nm scale then each division on the grip graduation is equivalent to 1.36Nm.
Therefore to set wrench at 100Nm:
• Turn grip until top edge of grip is level with the 94.9Nm line on the handle scale and the zero graduation on
the grip is aligned with the centre line of the handle scale.
• Rotate the handle further, clockwise, until the ‘4’ graduation on the grip is aligned with the centre line to
give a setting of 94.9 + (4 x 1.36) = 94.9 + 5.44 =100.34Nm
3.4.
Tighten the knurled lock screw at the end of the handle to prevent accidental alteration of the setting.
3.5.
When tightening the nut/bolt you will feel and hear the wrench mechanism click when the set torque is reached.
Immediately stop applying force to the wrench to avoid overtightening the nut/bolt. The torque wrench will reset
ready for the next application.
Note: If the torque wrench has not been used for some time, operate it a few times, at a low setting, to
ensure all internal parts are coated in grease.
3. OPERATION
4. RECALIBRATION
4.1.
In order to ensure continued accuracy, the torque wrench should be recalibrated annually and after any
impact or other misuse. Contact a NAMAS accredited laboratory.
Original Language Version