manualshive.com logo in svg

ITech IT-M7700 Series, Programming Manual

Share
Download
ITech IT-M7700 Series Programming Manual Download Page 4

 

 

IT-M7700 Programming Guide 

 

Copyright©  Itech Electronic Co., Ltd. 

iv 

Safety Precautions 

The  following  safety  precautions  must  be  observed  during  all  phases  of 
operation of this instrument. Failure to comply with these precautions or specific 
warnings  elsewhere  in  this  manual  will  constitute  a  default  under  safety 
standards  of design, manufacture and intended use of the instrument. ITECH 
assumes no liability for the customer’s failure to comply with these precautions. 

 

⚫

 

Do not use the instrument if it is damaged. Before operation, check 
the casing to see whether it cracks. Do not operate the instrument in 
the presence of inflammable gasses, vapors or dusts. 

⚫

 

The instrument is provided with a power cord during delivery and 
should be connected to a socket with a protective earth terminal, a 
junction box or a three-phase distribution box. Before operation, be 
sure that the instrument is well grounded. 

⚫

 

Please always use the provided cable to connect the instrument. 

⚫

 

Check all marks on the instrument before connecting the instrument 
to power supply. 

⚫

 

Ensure the voltage fluctuation of mains supply is less than 10% of the 
working voltage range in order to reduce risks of fire and electric 
shock. 

⚫

 

Do not install alternative parts on the instrument or perform any 
unauthorized modification. 

⚫

 

Do not use the instrument if the detachable cover is removed or 
loosen. 

⚫

 

To prevent the possibility of accidental injuries, be sure to use the 
power adapter supplied by the manufacturer only. 

⚫

 

We do not accept responsibility for any direct or indirect financial 
damage or loss of profit that might occur when using the instrument. 

⚫

 

This instrument is used for industrial purposes, do not apply this 
product to IT power supply system. 

⚫

 

Never use the instrument with a life-support system or any other 
equipment subject to safety requirements. 

 

 

⚫

 

SHOCK HAZARD Ground the Instrument. This product is provided 
with a protective earth terminal. To minimize shock hazard, the 
instrument must be connected to the AC mains through a grounded 
power cable, with the ground wire firmly connected to an electrical 
ground (safety ground) at the power outlet or distribution box. Any 
interruption of the protective (grounding) conductor or disconnection 
of the protective earth terminal will cause a potential shock hazard 
that could result in injury or death. 

⚫

 

Before applying power, verify that all safety precautions are taken. All 
connections must be made with the instrument turned off, and must 
be performed by qualified personnel who are aware of the hazards 
involved. Improper actions can cause fatal injury as well as 
equipment damage. 

⚫

 

SHOCK HAZARD, LETHAL VOLTAGES This product can output the 
dangerous voltage that can cause personal injury, and the operator 
must always be protected from electric shock. Ensure that the output 
electrodes are either insulated or covered using the safety covers 

Summary of Contents for IT-M7700 Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands