manualshive.com logo in svg

ITech IT-M7700 Series, Programming Manual

Share
Download
ITech IT-M7700 Series Programming Manual Download Page 28

 

 

STATus Subsystem 

 

Copyright©  Itech Electronic Co., Ltd. 

16 

Arguments 

None 

Returns 

<NR1> 

The value returned is the binary-weighted sum of all bits set in the register. 

STATus:QUEStionable:ENABle 

Sets the value of the enable register for the Questionable Status group. The 

enable register is a mask for enabling specific bits from the Operation Event 

register to set the QUES (questionable summary) bit of the Status Byte register. 

Syntax 

STATus:QUEStionable:ENABle <NR1> 

Arguments 

0~255 

The value returned is the binary-weighted sum of all bits set in the register. 

Default value 

See *PSC. 

Example 

STATus:QUEStionable:ENABle 128 

Query Syntax 

STATus:QUEStionable:ENABle?

 

Returns 

<NR1> 

The value returned is the binary-weighted sum of all bits set in the register. 

STATus:QUEStionable:NTRansition 

Sets the value of the NTR (Negative-Transition) registers for the Questionable 

Status group. 

Syntax 

STATus:QUEStionable:NTRansition <NR1> 

Summary of Contents for IT-M7700 Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands