background image

Green Heating Technology

30

Venting the primary exchanger

When commissioning the boiler, we recommend to check that there is no air in the primary circuit of 

the combustion unit. Do this operation also during the combustion unit cleaning, if you hear the typical 

air bubble noise. 

 

f

Locate the 

combustion unit manual venting valve

 (item

 8

 in the following picture) and, to avoid wet

-

ting the boiler inside, insert a length of flexible hose, with suitable diameter, on its fitting, then direct 

the other end towards a drain (or a container to collect the anti-freeze solution);

 

f

start the "circuit venting" mode by activating the

 Parameter 07

 (see "Main boiler parameters (PC)" 

on page 32);

 

f

slowly open the venting valve

 8

 and restore the system pressure when necessary; 

 

f

when no more air comes out from the venting valve

 8

, close the valve and reset the 

parameter 07

 

to

 0

;

 

f

restore the system pressure and, if needed, the concentration of additive liquid.

Combustion group cleaning and check

  Switch  off  the  boiler  and  disconnect  it 

from the electrical supply.

 

Be sure that the parts are not hot and 

eventually wait the time necessary to cool 

them;

  Because some contacts with the fine dust 

and acid condense may occur, we recom-

mend to wear the proper devices for the 

personal  protection  (i.e.  glasses,  gloves, 

masque)

  Warning:  do  not  wash  or  damage  the  in

-

sulating  coverings  inside  the  combustion 

chamber�

  The replacement of gasket on the ends of 

the pipe 04 is mandatory. Please get the 

original spares.

 

f

Open the sealed chamber;

 

f

disconnect the two connectors

 2

 from the fan;

 

f

disconnect the connector

 10

 from the ignition/

detection  electrode

  11

� 

Attention: 

do not dis-

mount the electrode from the combustion group

;

 

f

remove the fastening clip

 3

; unscrew the nut

 5

 

which fixes the gas pipe

 4

 to the gas valve; pull 

out the gas pipe

 4

 from the fan/air-gas-mixer assembly;

 

f

loosen the clamp

 10

 and pull the flexible air intake hose

 11

 out from the fan;

6

7

9
8

14

13

10

12

11

1

2

4

5

3

00325 01

Summary of Contents for 35 K

























































Reviews: