background image

Setting up SGZA10 and 

network 

 

Setting Up Summary 

 

(1)  Configure the device to either as a gas or a water keeper 
(2)  Power up the device and network association 
(3)  Bind the device with other device where applicable (i.e. bind with an on/off remote or 

with a smoke detector). 

(4)  How to use. 

 
 

Step 1: Configure the device to either as a gas or a water keeper

 

SGZA10 can only either be a gas keeper type or a water keeper type device. Before you 

move on to 

Step 2

, you will need to go through the 

Restore to Factory Setting 

section to 

configure the type of device you want -

a gas keeper 

or 

a water keeper

 

 

 

The difference between the two device types is that if it is a gas keeper it will receive fire 

alert message  from  the  paired smoke  detector of  the  security  network  to  turn  down  the 

leaver. If it is a water keeper it will receive on or off instruction from a remote controller by 

the user. 

 

 

Step 2: Power up the device and network association

 

To allow SGZA10 to function, it must first join to a ZigBee network either through a 

coordinator or a router device. When it is given power it will automatically start searching 

for an existed network. So before you give power to SGZA10 make sure it is within the 

wireless coverage distance (~70 meters or less) and make sure 

first 

you have the 

permit-join feature enabled 

either on a coordinator or a router device from the network 

so that SGZA10 can detect and automatically join to the network through it; 

*

On how to enable permit-join please refer to the router or coordinator device user manual 

 

 

Operation:

 

Step 1: First make sure you have opened up permit-join function (valid for 60 seconds) on 
a coordinator or a router device in the network. 
Step 2: Now plug  in the power  supplied provided  to power  on the  SGZA10 device to let it 

Summary of Contents for SGZA10











Reviews: