Isotta ALPHA 7RIII Instructions Manual Download Page 10

10

1.

  A  water-tight  test  without  the  camera  inside  the  housing  is  highly  recommended 

when using the system for the first time and after the changing of port and O-Ring(s).

2.

 O-rings should be kept clean and lubricated at all times. Discontinue use immediately 

should  you  notice  any  leakage.  Do  not  use  lubricants  from  other  brands  with  the 
silicone rubber O-ring on this housing, only use the lubricant provided by 

ISOTTA

  After checking the O-ring to make sure that there are no scratches, dust, or debris, 

apply a light coating of silicone grease to the entire O-ring with your finger. 

  Applying too much grease will make it easier for dust and debris to adhere to the 

O-ring, and could cause flooding.

3.

 When fitting the O-ring into the O-ring groove, insert it straight into the groove; do not 

bend or twist it.

4.

  Store  the  housing  in  a  robust,  shock-proof  container  during  transportation;  avoid 

transporting with any equipment, such as a camera, inside the housing, to avoid breakages.

5. 

When travelling by air, please remove the port from the housing as this may lead to damages.

6.

 Do not open the housing in a sandy environment. Protect the interior from moisture and 

debris in order to prevent malfunction or leakage.

7. 

 Do not store the housing in an environment of high humidity.

8.

 Do not leave the housing and the camera in direct sunlight for prolonged periods.

9.

 Do not store the housing in high temperature environment as in the car cockpit under the sun.

10.

 Keep out of reach of children, failure to do so could result in injury. 

11. 

Always dry the front port, the lens, the flash window or the finder using a soft cloth 

to prevent stain or salt residue from marring the glass surface.  Do not use solvent or 
alcohol to clean the port, viewfinder or LCD window.

12.

 When not in use the case for long time O-rings should be removed and stored sepa-

rately. Replace the O-rings once a year for a secure watertight. 
Use only Isotta O-rings.

13.

 Rinse the product with fresh water, after underwater use. Ensure that the product is 

waterproofed before rinsing. After each dive it is recommended to remove the port 
from the housing in order to avoid the possibility that the port gets stuck. Storage of 
the housing is possible only after cleaning and drying its surface.

14.

 Unauthorized  disassembling  and/or  modification  could  result  in  malfunction  or 

flooding, and void product warranty. Take the product to a ISOTTA authorized reseller 
for repair or inspection.the housing is possible only after cleaning and drying its surface.

PRECAUTIONS

Summary of Contents for ALPHA 7RIII

























Reviews: