background image

 

3A 

y

 The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly 

damaged. 

Caution 

There are no user serviceable parts inside this unit. Do not open the housing or attempt 

any repairs yourself. In the unlikely event your unit may require service, please contact 

your nearest dealer.

 

Installation 

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit 

is firmly fixed to avoid vibration and slipping while operating. And make sure that the 

structure to which you are attaching the unit is secure and is able to support a weight of 10 

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the 

weight of the unit when installing the fixture.   

The equipment must be fixed by professionals. And it must be fixed at a place where is out 

of the touch of people and has no one pass by or under it. 

 

2. Technical Specification   

y

  iMove 50S is the combination of the latest high powered LED technology, excellent optics 

and great features. 

y

  DMX control: 8/11 channels selectable. 

y

  3 operation modes: DMX, Master/Slave, Sound Activation. 

y

  Great built-in lighting programs under master/slave mode triggered by music. 

y

  Optional CA-8 easy controller or CA-9 RTX (wireless easy control kit) for instant lighting 

shows. 

y

  Rotating gobo wheel with 6 gobos plus white. 

y

  Color wheel with 8 colors plus white. 

y

  Beam angle: 15° 

y

  Automatic Pan/Tilt position correction. 

y

  Smooth 0~100% dimming and variable strobe speeds. 

y

  LED display for easy navigation and addressing. 

y

  Perfect for disco, club, bar, parties and Mobile DJs. 

y

  Pan: 540°. Tilt: 270° 

 

 

 

 

16A

4.5 DMX512 Connection   

3

2

DMX -

1

COMMON

DMX +

3

1

2

DMX INPUT

DMX OUTPUT

2

3

1

Termination reduces signal errors and avoids signal
transmission problems and interference. It is always
advisable to connect a DMX terminal.
(Resistance 120 ohm 1/4W)between pin2(DMX-)and
pin3(DMX+) of the last fixture.

 

1.  If you are using a controller with 5 pins DMX output, you need to use a 5 to 3 pin 

adapter-cable. 

2.  At the last unit, the DMX cable has to be terminated with a termination plug. Solder a 

120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug 

and plug it in the DMX-output of the last unit. 

3.  Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to 

the input of the next unit. The cable can not be branched or split to a `Y` cable. DMX 

512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or 

corroded connectors can easily distort the signal and shut down the system. 

4.  The DMX output and input connectors are pass-through to maintain the DMX circuit, 

when one of the units’ power is disconnected. 

5.  Each lighting unit needs to have an address set to receive the data sent by the 

controller. The address number is between 1-512 (usually 0 & 1 are equal to 1). 

6.  The end of the DMX 512 system should be terminated to reduce signal errors. 

7.  3 pin XLR connectors are more popular than 5 pin XLR. 

Summary of Contents for iMove 50S











Reviews: