background image

8- 

  4. How To Set The Unit   

 

  4.1 Control Panel   

 

 

 

Display 

To show the various menus and the selected functions . 

LED 

  DMX 

  On 

  DMX input present 

  MASTER 

  On 

  Master Mode 

  SLAVE 

  On 

  Slave Mode 

  SOUND 

  Flashing 

  Sound activation 

Button 

  MENU 

  To select the programming functions 

  DOWN 

  To go backward in the selected functions 

  UP 

  To go forward in the selected functions 

  ENTER 

  To confirm the selected functions 

 

Remote controller input 

By connect to the 1/4

 microphone jack to control the unit for Stand by, Function and Mode 

Sensitivity 

To adjust the sound sensitivity . 

Microphone 

To receive audio signal for sound activation . 

DMX input/output 

For DMX512 link, use 3-pin XLR plug cable to link the unit together. 

 

  5. How To Control The Unit 

 

        You can operate the unit in three ways: 

 

1. By master/slave built-in preprogram function 

  2. By easy controller 

  3. By iLead controller ( please refer to the user guide of iLead ) or by universal DMX 

controller 

No need to turn the unit off when you change the DMX address, as new DMX address setting 

will be effected at once. Every time you turn the unit on, it will show IM8S / IM7S on the 

display and move all the motors to their 

home

 position and you may hear some noises for 

about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in 

programs. 

 

  5.1 Master/Slave Built-In Preprogrammed Function   

 

You can select blackout mode 

  in 

  (yes blackout) or 

  (no blackout) 

mode while the unit is turned on. By linking the units in master/slave connection, the first unit 

will control the other units to give an automatic, sound activated, synchronized light show. 

This function is good when you want an instant show. You have to select 

  (show 1) or 

  (show 2) or 

  (show 3) or 

  (show 4) mode by easy controller. Its 

DMX input jack will have nothing plugged into it, and Its master LED will be constantly on and 

sound LED will flash to the music. The other units will have to set in slave mode 

  and 

select 

  (normal) or 

  (2 light show) mode, Their DMX cables plugged into the 

DMX input jacks (daisy chain) and the slave LED lights will constantly on. 

 

2-light show 

 

In 

  (slave mode), 

  means the unit works normally and 

  means 2-light 

show. In order to create a great light show, you can set 

  on the second unit to get 

contrast movement to each other, even if you have two units only. 

 

  5.2 Easy Controller   

The easy remote controller is used only in master/slave mode. By 

connecting to the 1/4

 microphone jack of the first unit, you will find that 

the remote control on the first unit will control all the other units for 

Stand by, Function and Mode. 

Summary of Contents for IH9000-1











Reviews: