21
252_EN_IS_1_3_00.doc
FUNCTI ON FOR OUTPUT 1, 2,3
q
OFF: DI SABLED
q
PLS: PULSE FOR POSI TI VE AND NEGATI VE FLOW RATE
q
PLS-: PULSE FOR NEGATI VE FLOW RATE
q
PLS+ : PULSE FOR POSI TI VE FLOW RATE
q
EXT. COMM.: ONLY AVAI LABLE WI TH DATA LOGGER MODULE
q
HARDW AL: CUMULATI VE ALARM OUT interrupt coils, empty pipe, meas. error (ENERG. = NO ALARMS)
q
OVERFLOW.: OUT OF RANGE ALARM OUTPUT (ENERGI SED = FLOW RATE OK)
q
EMPTY PI PE: EMPTY PI PE ALARM OUTPUT (ENERGI SED = FULL PI PE)
q
MAX+ MI N± : MAX AND MI N FLOW RATE ALARM OUTPUT (ENERGI SED = AL. OFF)
q
MI N AL± : MI N DI RECT/ REVERSE FLOW RATE OUTPUT(ENERGI SED = AL. OFF)
q
MI N AL-: MI N REVERSE FLOW RATE OUTPUT(ENERGI SED = AL. OFF)
q
MI N AL+ : MI N DI RECT FLOW RATE OUTPUT(ENERGI SED = AL. OFF)
q
MAX AL: MAX DI RECT/ REVERSE FLOW RATE OUTPUT(ENERGI SED = AL. OFF)
q
MAX AL-: MAX REVERSE FLOW RATE OUTPUT (ENERGI SED = AL. OFF)
q
MAX AL+ : MAX DI RECT FLOW RATE OUTPUT ( ENERGI SED = AL. OFF)
q
RANGE: RANGE I NDI CATI ON OUTPUT (ENERGI SED = SCALE 2)
q
SI GN: FLOW DI RECTI ON OUTPUT (ENERGI SED = -)
again. Allowed values for this parameter: ON / OFF.
N.B.:
the autorange doesn’t allow using the
manual change of range (see pos. 5.8)
( POS. 3.5) Energy saving enable
[E.SAVI NG= ON/ OFF]
Enable automatic energy saving function. This function I F ON, ENABLES THE OPERATI ON OF THE
METER I N ACCORDANCE WI TH I NTERVALS OF FI XED TI ME WI TH THE FOLLOWI NG FUNCTI ON; if
OFF the measure is continuous at 10 Hz of frequency. Allowed values for this parameter: ON/ OFF
MENU 6. OUTPUT
( POS. 6.1- 6.2) Function corresponding to on/ off output 1- 2
[ OUT 1- 2= XXXXXX]
Choice of the function corresponding to digital Output 1-2. The functions are listed in the table
below
MENU 8.DI SPLAY
( POS. 8.2- 8.3- 8.4- 8.5) Reset totalizer
[ T/ P+ / - RESET= ON/ OFF]
Reset of totalizer by key board;
N.B.:
The reset of the totaliz . ma y be done from the function listed upon pushing the key
and the key . The reset of partial totalizer / currency may be done also from the visualization
pages at page 12 like this . Push the key . Set the L2 CODE if request and then push the
key . At the question “RESET TOTALI Z.?”. Push the key to proceed with the zeroing.
Push any other key to cancel this operation.
( POS. 8.9) Enable conversion currency
[ CURRENCY = ON/ OFF]
This function visualizes the values of the partial totalizators converts in the unite of selected
currency.
( POS. 8.10) Decimal currency
[ CURR DECI M = X]
This function allows the choice of the numbers of decimals to use for the visualization of the
numerical value converted in the currency. The allows values are from 0 to 3. The function is active
only if the currency function is enable
( POS. 8.11- 8.12) Conversion factor for flow rate totalizers
[ EUR/ dm
³ +
= X]
Set the value of conversion/ currency for totalizers. There are three fields for this parameter, from
left to right:1) monetary token, 2 ) default/ personalized monetary token, 3 ) conversion coefficient.
For the selection setting the cursor over the field to modify. The mode set of monetary token could
be two:
•
choice of one of the 7 predetermined monetary tokens (standard I SO 4217-REV81):
EUR = Eur, USD = USA dollar, CAD = Canadian dollar, AUD = Australian dollar, GPB = English
pound, CHF = Swissfranc, JPY = Japanese yen.
