manualshive.com logo in svg

Iseki SCMA48F, Introduction Manual, Page: 46 / 52

Share
Download
Iseki SCMA48F Introduction Manual Download Page 46

SFH220 & SFH240 FRONT MOWER SERVICE MANUAL

46

・

Foreign matter caught in shaft

・

Broken wheel

・

Short of grease 

・ 

Inside of the mower deck is clogged with 

    too much grass or mud.

・

Defective hydraulic system

Troubles Presumable 

causes  Remedies

・ 

Excessive noise and  vibration

・

Too low engine output

・

Gauge wheels do not turn.

・

Mower does not rise.

・ 

Clogged grass inside of mower or foreign 

    matter caught in a pulley

・ 

Deformed or interfering belt cover or shaft 

    cover

・

Damaged bevel gears

・

Broken or unbalanced blades

・

Loose blade tightening nuts

・ 

Slipping blade belt (SMM54F)

・

Too low engine speed

・

Too fast travelling speed

・ 

Foreign matter caught between blade and 

    blade support

・

Foreign matter caught in a pulley

・

Defective engine

・

Clean.

・

Repair it.

・

Consult your dealer.

・

Replace them with new ones.

・

Re-tighten them to 1300 kgf

・

cm. 

・

Adjust belt tension spring 

    properly.

・

Mow at full throttle (

r

).

・

Slow down.

・

Clean.

・

Clean.

・

Consult your dealer.

・

Clean.

・

Replace it with a new one.

・

Inject grease.

・

Clean.

・

Consult your dealer. 

・

Loose blade tightening nuts

・ 

Foreign matter caught in blades or blade 

    supports

・

Broken bevel gears

・

Broken blade pulley

・

Slipping blade belt

・ 

Center PTO clutch is slipping or not 

    engaging. 

・

Blades do not rotate.

・

Re-tighten them to 1300 kgf

・

cm. 

・

Clean.

・

Consult your dealer.

・

Replace it with a new one.

・ 

Adjust belt tension spring properly.

・

Consult your dealer.

Summary of Contents for SCMA48F





















































Reviews:

No comments