iseg EHQ 1 Series Technical Documentation Manual Download Page 37

Page: 37 / 46

9.6. Module EventStatus (read access)

:READ:MOD

ule

:EV

ent

:STAT

UI2

Bit15

Bit14

Bit13

Bit12

Bit11

Bit10

Bit09

Bit08

Reserved

Event
Temperature
Not Good

Event Supply
Not Good

Reserved

Event Safety
Loop Not
Good

Reserved

Bit07

Bit06

Bit05

Bit04

Bit03

Bit02

Bit01

Bit00

Reserved

Event Service

Reserved

Status Bit

Description

Event Temperature Not Good

Temperature is above 55°C

Event Supply Not Good

at least one of the supplies is not good

Event Safety Loop Not Good

Safety loop is open

Event Service

A hardware failure of the HV module has been detected. The HV is switched off without the
possibility to switch on again. Please

consult

the iseg Spzialelektronik GmbH.

EHQ High Voltage Power Supply series | Last changed on: 11.05.2020 |

www.iseg-hv.com

37/46

Summary of Contents for EHQ 1 Series















































Search results

Summary of Contents for EHQ 1 Series

Reviews:

Related manuals for EHQ 1 Series

Brands by name

Popular brands

iseg EHQ 1 Series, Technical Documentation Manual

Search results

Summary of Contents for EHQ 1 Series

Reviews:

Related manuals for EHQ 1 Series

Brands by name

Popular brands