manualshive.com logo in svg

iS5 iES10G Series, User Manual

Share
Download
iS5 iES10G Series User Manual Download Page 63

iES10G(F)  User  Manual 

 

iS5 Communications Inc. 

63 

The following table describes the Port Statistics interface page. 

Label 

Description 

Type

 

Shows port speed and media type. 

Link 

Shows port link status. 

State 

Shows port enabled or disabled. 

TX GOOD Packet 

The number of good packets sent by this port. 

TX Bad Packet   

The number of bad packets sent by this port. 

RX GOOD Packet 

The number of good packets received by this port. 

RX Bad Packet 

The number of bad packets received by this port. 

TX Abort Packet 

The number of packets aborted by this port. 

Packet Collision 

The number of times a collision detected by this port. 

Clear 

Clear all counters. 

Help 

Show help file. 

 

 

5.1.14.4

 

Port Monitoring 

The  Port  Monitoring  function  supports  TX  (egress)  only,  RX  (ingress)  only,  and  both  TX/RX  monitoring.  TX 

monitoring  sends  any  data  that  egresses  out  of  the  Source  Port  to  another  port  for  monitoring.  Check  TX 

Source Ports to a selected TX destination port. RX monitoring sends any data that ingress in to the Source Port 

to another port for monitoring. Check RX Source Ports out to a selected RX destination port. It also sends the 

frame where it normally would have gone. Note: keep all source ports unchecked to disable Port Monitoring. 

 

Port monitoring interface 

 

Summary of Contents for iES10G Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands