IronStrike Winslow PI40GL Installation And Operation Manual Download Page 29 | Manualshive

Page: 29 / 42

IronStrike Winslow PI40GL Installation And Operation Manual Download Page 29

29

Orange Sooty Flames - Glass turns Black

Possible Problem

Solution

Burn-Pot is dirty

Clean the Burn-Pot

Vent pipe restricted

Clean the vent pipe

Flue gas passageways restricted

Clean the passageways

Combustion blower dirty

Clean the combustion blower

Burning improper fuel

Burn only wood pellet fuel or corn fuel that meets the fuel speci-

fications outlined on Page 7

Pellets not Feeding

Possible Problem

Solution

Hopper empty

Fill the hopper

Auger jammed

Call service technician

Flue gas passageways restricted

Call service technician

Auger motor not operating

Call service technician

Hopper lid is open

Close Hopper Lid

Hopper lid switch is faulty

Replace hopper lid switch if determined to be faulty

Over Temperature Snap Switch Shuts Insert Down - Code - Ready light flashes red 2 long blinks

Possible Problem

Solution

Convection blower not running

Blower dirty, blower snap switch bad, or blower broken

Flue passageways or vent restricted

Clean passageways or vent pipe (see Pages 22 and 23)

Snap switch* defective

Replace the snap switch*

* NOTE: The snap switch has a reset button that must be pushed before insert will function (see Page 26).

«
...
27
28
29
30
31
...
»

Summary of Contents for Winslow PI40GL











































Reviews:

No comments