12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1. Burn only dry, well-seasoned wood for maximum heat output. In some
states it is illegal to burn wet wood or anything other than clean, dry
wood products.
2. Your stove or fireplace insert is designed to operate with the door
closed! Operate only with the door shut tightly at all times except when
loading wood and possibly on start up to establish a draft. Never
leave the unit unattended while the front door is slightly opened.
3.
DO NOT
hit or move the baffle boards while loading wood. Occasion-
ally check the baffle. Make sure the baffle blanket is always flush with
the front of the baffle boards. Loading oversized logs may dislodge
the baffle boards.
4.
CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN
BEFORE OPENING THE DOOR TO AVOID POSSIBLE COMBUS-
TION FLASH!!
(Ignition of hot volatile gases as the door is opened).
5. Feeding excessive amounts of fuel to the stove or fireplace insert
should be avoided. It is important to supply it with sufficient draft
and fuel to maintain a moderately hot fire. If, during overnight burns,
heavy creosote deposits develop inside your stove or fireplace insert
and on the door, the draft is set too low - review your burning habits!
OPERATING HINTS
Be sure to clean plated accessories with a household type glass
cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire.
1.
NEVER USE FLAMMABLE LIqUIDS TO START OR REKINDLE
A SOLID FUEL FIRE!!
2. Fully open the primary draft control by pulling the 1” plastic knob
out on the left side (lower front corner) until it stops (away from the
fireplace insert). This control determines the amount of air entering
the fireplace insert. Pushing it towards the fireplace insert reduces
the burn rate in the firebox. For your convenience, the rod on this
control is marked with four grooves to assist you in obtaining repeat-
able burn rates.
3. Place a small amount of crumpled paper in front of the firebox and
cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling to become
fully engulfed in flames. You will now close the wood units front door.
(Your wood units front door may or may not need to be left slightly
open during this start up process, this depends on the appliance model
and the amount of draft present. Do not leave the unit unattended
while the front door is slightly open) Once kindling is burning well,
larger pieces of wood may be added, then the door should be fully
closed if there was the need to keep it slightly open during start up.
DO NOT LEAVE THE APPLIANCE UNATTENDED WHILE THE
FRONT DOOR IS SLIGHTLY OPEN.
CAUTION: Do Not alter the adjustment range of the draft
control for increased firing for any reason.
Operate only with fuel door and ash drawer closed. Maintain
all seals in good condition. Do not operate with broken glass.
Do Not build the fire too close to the glass.
Do not operate the appliance with the door open or ajar other
than possibly during start up to create a draft (Do not leave
the unit unattended while the front door is slightly open dur-
ing start up). Operating the appliance with the door open
other then in initial start up if needed will produce extreme
temperatures within the appliance. Damage caused from
over-firing is not covered under the manufacturers limited
warranty.
5.
When operating any wood burning appliance, it is important to
become familiar with how the damper control affects heat output
and the overall temperature of the appliance. A stove thermometer
can be a helpful tool to help ensure you are not over-firing your
appliance and it will also ensure you are burning fuel at a rate that
is most efficient. Place a stove thermometer on the top of the ap-
pliance. Monitor the temperature every 15 minutes or so until you
become more familiar with your appliance. Close the damper all
the way down if you begin to reach 600 degrees, as this is a sign
that you are operating your appliance at too high a temperature.
6. For best results, use smaller pieces of wood to get the stove or
fireplace insert temperature very high before loading larger wood for
sustained burns. If necessary, crack the door to allow ignition of the
fuel charge.
Do not leave the unit unattended while the front door
is slightly open
. Now you can add larger pieces of wood and after
several minutes of high burn, set the left control for the desired heat
output. Check the exhaust in about 15 to 20 minutes. Large amounts
of smoke indicate an improper burn setting (either too high or too
low). Adjust and recheck in 5 to 10 minutes.
Figure 10
STARTING AND MAINTAINING A FIRE
OK
WARNING
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replace-
ment parts.
