background image

7

Attach Actuator (C) to Lower extension Arm
(F).

Slide Actuator plastic sleeve (D) over top of
Actuator (C), align the hole in the Plastic sleeve
with the hole in the Actuator, slide one Steel
Sleeve (#5) thru both parts, see Figure 8.
Hold the Actuator assembly, align Steel Sleeve
with the Rear hole of Lower extension Arm (F),
Attached them together with one Hex bolt
M12x205 (#3), two Flat washers M12 (#8), Two
Nylon washers (#1) and one Lock nut M12 (#9).
Do not over tighten the bolts.

Attached Actuator (C) to Actuator mounting
plate (E).

See Figure 11

Attach Crank (L) to the bottom of Actuator with
supplied Lock pin.

Crank Actuator in between two Mounting plate
(E), secure them together with one Hex bolt
M12x105 (#4), two Flat washer M12 (#8), two
Nylon washers M12 (#1), and one Lock nut (#9).

Do not over tighten this bolt.

Note

make  sure  Plastic  washers  go  between

:

Mounting plate (E) and Actuator (C). It prevents
painted parts from being scratched.

8.

9.

Slide Plastic sleeve
over Actuator

STEP 8

STEP 9

Figure 11

Figure 12

Attach Goal (I) to Backboard (H).

Remove the Rim box cover, put Goal
against Rim pad (Pre-installed), secure it
with 4 Hex bolts M10x45 (R1), 8 Flat
washers M10 (R2),  4 Flange nuts M10
(R3) See Figure 12.

Tighten all four bolts and nuts.

Put Rim box cover back and secure it with
removed screws.

10.

3

8

1

8

9

D

C

C

5

4

8

1

8

9

L

B

R1

R2

R2

R3

H

I

Summary of Contents for GC55-MD









Reviews: