background image

 

16 

 

 

RESETS 

 
WARNING: USE OF THE RESET FUNCTIONS IS NOT RECOMMENDED EXCEPT UNDER THE 
GUIDANCE OF A WATER TREATMENT PROFESSIONAL FAMILIAR WITH THIS EQUIPMENT. 
 

Soft Reset: 

Press and hold the EXTRA CYCLE and DOWN buttons for 25 seconds while in 

normal Service mode. This resets all parameters to the system default values except days since 
regeneration in the time clock system. 

 
Master Reset: 

Hold the Extra Cycle button while powering up the unit. This resets all of the 

parameters in the unit. Check and verify the choices selected in Master Programming Mode.

 

 
 

 

CONTROL OPERATION DURING A POWER 
FAILURE 

 

The 2510SXT valve/controller includes integral power backup. In the event of power failure, the 
control shifts into a power-saving mode. The control stops monitoring water usage, and the display 
and motor shut down, but it continues to keep track of the time and day for a minimum of 48 hours. 
 
The system configuration settings are stored in a non-volatile memory and are stored indefinitely 
with or without line power. The Time of Day flashes when there has been a power failure. Press any 
button to stop the Time of Day from flashing. 
 
If power fails while the unit is in regeneration, the control will save the current valve position 
before it shuts down. When power is restored, the control will resume the regeneration cycle from 
the point where power failed. Note that if power fails during a regeneration cycle, the valve will 
remain in it’s current position until power is restored. The drain line plumbing configuration should 
include all required safety components to prevent overflows resulting from a power failure during 
regeneration. 
 
The control will not start a new regeneration cycle without line power. If the valve misses a 
scheduled regeneration due to a power failure, it will queue a regeneration. Once power is restored, 
the control will initiate a regeneration cycle the next time that the Time of Day equals the 
programmed regeneration time. Typically, this means that the valve will regenerate one day after it 
was originally scheduled.  
 
 
 
 
 
 
 
 

Summary of Contents for IR-10-B




















Reviews: