Iron Rival IR-10-B Owner'S Manual & Installation Manual Download Page 19

 

19 

This warranty does not cover: 
 

A.  Exclusions applicable to all Pentair Water Treatment products: 

1. Defects not reported to Pentair Water Treatment with the above described warranty period. 
2. Any items manufactured by other companies. Such items may carry warranties offered by the original manufacturers. 
3. Problems resulting from failure to comply with installation instructions or drawings, or improper installation. 
4. Damage caused by acts of nature or problems resulting from abuse, misuse, negligence or accident by any party other     
    than Pentair Water Treatment. 
5. Problems resulting in whole or in part from alteration, modification or attempted repair of these Products or Parts by any  
    party other than Pentair Water Treatment. 
6. Pistons, Seals, Spacers, and Brine Valves on all hot water valves. These parts require maintenance as part of a yearly 
    service schedule. 
7. Noncompliance with applicable codes, and ordinances including without limitation, plumbing codes. 
8. Damage due to chemical attack. 

 

B.  Additional exclusions applicable Structural PolyGlass Composite FRP branded products: 

1. Warranty applies only to original owner at the original installation location. 
2. Failure to adhere to installation and operation instructions, including failure to operate tank in accordance with  
    limitations stated of product label. 
3. Failure to properly size tank to pump manufacturer's recommendations. 
4. Use of product with water containing sediment or chemicals. 
5. Injury to tank or any part thereof caused by exposure to vacuum, freezing, external impact, chemical attack from liquid  
    and gasses, fire, floods and lightning. 

 

C.  Specific exclusion applicable to PolyGlass branded products: 

Use in applications other than residential water softeners and filters. 

 
WARRANTY OBLIGATIONS OF PENTAIR WATER TREATMENT 

– Should a defect in workmanship and/or material in 

Products or Parts covered by this warranty become evident during the term of the warranty, then upon compliance with the 
procedures, as set forth below, Pentair Water Treatment, at its option, will: In the case of Products, issue a credit in the amount of the 
original purchase price of the product, or repair or replace the defective Products. Pentair Water Treatment will consider, in good 
faith customer preference in making a determination whether to issue a credit or repair or replace a Product. In the case of Parts, 
whether purchased new or exchanged on a Product by other parts, Parts may not be returned for credit or repair. Pentair Water 
Treatment will only be responsible for the replacement of defective Parts. 
 

PROCEDURE FOR OBTAINING WARRANTY PERFORMANCE 

– 

A. In order to obtain the benefits of this Limited Warranty, defective Products and/or Parts must be returned to Pentair Water 
Treatment as soon as possible after discovery of the defect, but in no event later than the expiration date of the warranty period 
provided in this Limited Warranty. The subject Product or Parts must be returned to the original point of shipment, freight prepaid, 
along with a letter stating the model number, serial number, if any, the date of purchase of the item which is claimed to be defective 
and a brief description of the problems encountered. Pentair Water Treatment is not responsible under this Limited Warranty for any 
cost of shipping or transportation incurred in connection with the return of the Products or Parts. 
 

NO OTHER WARRANTIES 

– To the maximum extent permitted by applicable law, PENTAIR WATER TREATMENT 

DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, with regard to the 
Product(s), Part(s) and/or any accompanying written materials. This limited warranty gives you specific legal rights. You may have 
others which vary from state/jurisdiction to state/jurisdiction. 
 

NO LIABILITY FOR CONSEQUENTIAL DAMAGES 

– To the maximum extent permitted by applicable law, in no event shall 

Pentair Water Treatment or your water dealer be liable for any damages whatsoever (including without limitation, loss of time, 
inconvenience, expenses such as telephone calls, labor or material charges incurred in connection with the removal or replacement of 
the Product(s) or Part(s), special, incidental, consequential, or indirect damages for personal injury, loss of business profits, business 
interruption, loss of business information, or any other pecuniary loss) arising out of the use of or inability to use the defective 
Product(s) or Part(s), even if Pentair Water Treatment has been advised of the possibility of such damages. In any case, Pentair Water 
Treatment's entire liability under any provision of this Limited Warranty shall be limited to the amount actually paid for the 
Product(s) or part(s). PLEASE NOTE: Because some states/jurisdictions do not allow the exclusion or limitation of incidental or 
consequential damages, the above limitation or exclusion may not apply. 
 

WARRANTIES OR REPRESENTATIONS BY OTHERS 

– No dealer or other person has any authority to make any warranties 

or representations concerning Pentair Water Treatment or its products. Accordingly, Pentair Water Treatment is not responsible for 
any such warranties or representations. 
 

OTHER RIGHTS 

– This warranty gives specific legal rights, and other rights may apply. Such rights vary from state to state. 

 

Summary of Contents for IR-10-B




















Reviews: