manualshive.com logo in svg

IPS TS33-ON Series, Installation Manual, Page: 38 / 39

Share
Download
IPS TS33-ON Series Installation Manual Download Page 38

SERIES

 

TS33-ON

 

 

 

www.ips-ups.eu                                                                                             

      

 

28.05.2018 

[email protected] 

 

 

 

 

                     TS33-ON-manual_EN-R0 

 

38 

SHORT/CA SHORT 

The fault indicator is 

illuminated, the sound of 

the buzzer lingers on, 

and emits fault 

information - OUER 

LOAd 

Overload 

Check the load level and 

disconnect the non-critical 

equipments, recount the 

total capacity of your load 

and reduce the load to the 

UPS. 

Check whether the load 

equipments has fault or not. 

The fault indicator is 

illuminated, the sound of 

the buzzer lingers on, 

and emits fault 

information -  AnEgPOW 

F/BnEgPOW 

F/CnEgPOW F 

Negative power is 

abnormal 

Contact the supplier.

。

 

Fan icon flashes, the 

buzzer beeps in every 4 

seconds, and emits 

alarm information- FAn 

FAIL 

Fan fault 

Check whether the fans are 

connected and fixed well or 

not and whether they are 

broken or not. If all seems 

fine, contact the supplier. 

The UPS fails to start 

when press ‘On’ key 

Pressing time too 

short 

Press the power key more 

than 2 seconds to start the 

UPS. 

The input connection 

is not ready or UPS 

internal battery 

disconnected 

Connect the input well, if 
the battery voltage is too 
low, disconnect the input 

and start the UPS with no-

load. 

Internal system fault 

Contact the supplier. 

The battery discharge 

time is too short 

Battery undercharge 

Keep the UPS battery 

recharging more than 3 

hours 

UPS overload 

Check the load level and 

disconnect the non-critical 

equipments. 

Battery maturing, 

capacity descend 

Replace with new batteries, 

contact the supplier to get 

the new batteries and spare 

parts. 

The mains power is 

normal but the UPS fails 

to access to mains 

power 

UPS input fuse is 

disconnected or 

input wiring is wrong 

Replace with new fuse or 

check input manner or 

contact the supplier 

Summary of Contents for TS33-ON Series








































Reviews:

No comments