English
- 21 -
PRELIMINARY OPERATIONS
UNPACKING
After unpacking, ensure that the cleaner is undamaged.
If in doubt, do not use the machine.
Contact your dealer.
Packaging (bags, boxes, nails, etc) is potentially dangerous and
should be kept out of reach of children. It should be disposed of
or retained in respect of national environmental legislation.
FITTING THE SEPARATE PARTS OF THE MACHINE
All the fundamental parts and safety devices of the machine are
assembled by the manufacturer.
For reasons of packing and transport, some secondary cleaner
parts are supplied separately.
The user must fit these parts as explained in the instructions
supplied in each assembly kit.
DATA PLATE:
The data plate bearing the main technical characteristics of your
cleaner is located on the trolley and is always visible.
When buying your cleaner, ensure that it has an
identification plate. If there is no plate, inform the manu
-
facturer and/or the dealer immediately. Machines without
a plate must not be used and the manufacturer declines all
responsibility for them. Products without a plate must be
considered anonymous and potentially dangerous.
INTENDED USE
This appliance is intended exclusively for cleaning machines,
vehicles, buildings and general surfaces suitable for treatment
with a high pressure jet of detergent solution between 25 and
250 bar (360 - 3600 PSI).
This appliance has been designed for use with the detergents
supplied or recommended by the manufacturer. The use of
other detergents or chemicals may influence the safety of the
appliance.
This appliance must be used only for the purpose for which it
was specifically designed.
All other uses are to be considered incorrect and therefore
unreasonable.
Examples of unreasonable use:
- Washing surfaces not suitable for cleaning with a high
pressure jet.
-
Washing people, animals, electric equipment or the machi-
ne itself.
-
Using unsuitable detergents or chemicals.
- Blocking the trigger (lever) of the lance in delivery posi-
tion.
The manufacturer cannot be held responsible for any damage
due to improper, incorrect or unreasonable use. As far as safety
rules are concerned, the cleaners are manufactured according
to the European Standard.
FIG. 1
Warning
Do not use different fuel from that indicated on the iden
-
tification plate.
Check the fuel level from time to time while the cleaner
is operating.
Attempting to use the cleaner without fuel may cause
damage to the fuel pump.
FILLING THE FUEL TANK
Fill the tank with fuel for Diesel
motors (fig. 1).
!
!
FIG. 3
FIG. 2
FILLING THE DETERGENT
TANK
Warning
From the range of recommen-
ded products, choose the one
most suited to the washing job
to be done (fig. 2) and dilute
it with water according to the
instructions on the pack.
Fill the detergent tank with the
diluted product (fig. 3).
Ask your dealer for the cata-
logue of the detergents that
can be used depending on
the type of washing job to be
done and the type of surface
to be treated.
After using a detergent, the
detergent intake circuit must
be flushed out with clean
water.
!
DieselDiesel
Chemical
Chemical
Summary of Contents for D 1713P T
