background image

-    -

 

 

I.

 

Important Safeguards

 

1. All the safety and operating instructions should be read before the units is operated.

2.Power supply for IR Dome Camera

DC12V. 

The 

power input power supply indicated on the

base of dome or other related marking label.

 

3.During the course of transportation, storage and installation, the product should be avoided

from incorrect operations such as heavy pressing, strong vibration etc, which can cause 

damage of product as there are sophisticated optical and electronic devices inside the machine. 

4.

Do not attempt to disassemble the camera. In order to prevent electric shock, do not remove

screws or covers. There are no user-serviceable parts inside.

 

5.

Always follow all electrical standards for safety when it is in operation. Adopt the particular

power supply which is provided with the unit. RS-485 and video signal should keep enough 

distance with high voltage equipments and cables when they are in transmission. Precautions 

for anti-lightning and anti-surging should be taken if necessary.

 

6. Do not operate it in case temperature, humidity and power supply are beyond the limited

stipulations.

 

7. Do not let the camera aim at the sun or the object with extreme light whatsoever it is

switched on or not. Do not let the camera aim at or monitor bright and standstill object for a 

long time.

 

8. Do not use aggressive detergent to clean the main body of the camera. Wipe dirt with dry

cloth. If needed, mild detergent can be used suitably.

 

9. Operate the intelligent speed dome camera with great care to avoid shock or vibration. It

operate incorrectly, the Speed Dome could be damaged.

 

10. Please ensure the installation position with enough endurance when you install the

intelligent IR High speed dome camera. 

11. If necessary, use a commercial lens cleaning paper to clear the lens windows. Gently wipe
the lens window until clean. 

II.

Description of Functions

This  Infra  Red  High  Speed  dome  Camera  uses  the  highly  integrated  16-bit  processor,  low 

power  consumption,  super  stable.  Built-in  high-power  infrared  array  light  inside,  ultra-high 
luminous efficiency, fill light uniform, smaller heat and night vision range up to 80 meters.

 

1.

Integrated Speed-Variable PAN/TILT

a. Turning  360ºh

  

orizontally  and  continuously  with unlimited  positions  and  an  adjustable

speed from 0.01 - 300 º

 /s; turning 0 - 90º

 vertically with a speed up to 120 º

 /s. 

Summary of Contents for MPTZ20XIRIP-HLC

















Reviews: