background image

The LED on the charger will illuminate, 
indicating that it is receiving power.

4

Place a Key onto the contacts in one 
of the charger slots. Allow the Key to 
charge for 6 hours before use.

5

Below is a breakdown of the IR4 Key’s LED 
indicators.
• Green - Battery and Timeout are good for 
   continued use.

• Yellow - Return the Key to the Manager 
   within the hour. Battery is low or Timeout is  
   close to expiration.

• Red - Return the Key to the Manager 
   immediately. Battery is too low for 
   continued use or the Key has timed out.

• No LED - Return the Key to the Manager 
   immediately. Battery is completely 
   depleted. 

3

Plug the power cable into a PS515 
power supply. Plug the power supply 
into a power outlet.

7a

Section 2: OneKEY Manager 

Installation 

Place the OneKEY Manager where 
desired and plug the PS512 power 
supply into the port on the back of 
the Manager. Plug the power supply 
into a power outlet.

If using the Single Key Charger 
(OK4101), slide the OneKEY into the 
charger. Ensure that the charging 
contacts on the OneKEY align with 
the charging contacts on the charger.

6

There are 2 versions of the OneKEY, here are the differences.

Batch Key 

(OK4000 & OK4000-S)

LIVE Key 

(OK4400, OK4401, 

OK4406 & OK4500)

Activity

Tracking

Remote Key 

Deauthorization

Parts 

Needed

Batch updates when 

docked with the 

OneKEY Manager

Real time data transfer 

over a LORA network

No

Yes

• OneKEY (Batch)
• OneKEY Manager & Power  
   Supply
• Single, 4x or 8x Charger & 
   Power Supply
• LAN Connection

• OneKEY (LIVE)
• OneKEY Manager & Power  
   Supply
• Single, 4x or 8x Charger & 
   Power Supply
• LAN Connection
• LORA Gateway

Summary of Contents for OneKEY










Reviews: