INVT MH860 Series Operation Manual Download

Page: 3 / 125

MH860 series hydraulic servo drive

Contents

Contents

Preface ........................................................................................................................................... i

Contents ....................................................................................................................................... ii

1 Safety precautions ..................................................................................................................... 1

1.1 Safety definition ................................................................................................................. 1

1.2 Safety guidelines ............................................................................................................... 1

2 Product overview ....................................................................................................................... 3

2.1 Product confirmation .......................................................................................................... 3

2.2 Drive nameplate................................................................................................................. 3

2.3 Drive model description...................................................................................................... 3

2.4 Drive specifications ............................................................................................................ 4

2.5 Drive technical performance ............................................................................................... 6

2.6 Dimensions of drive ........................................................................................................... 7

2.6.1 Dimensions of air-cooled drive ................................................................................. 7

2.6.2 Dimensions of liquid-cooled drive ............................................................................. 9

2.7 Motor nameplate .............................................................................................................. 10

2.8 Motor model description ................................................................................................... 10

2.9 Motor specifications ......................................................................................................... 11

2.10 Motor installation dimensions ......................................................................................... 12

3 Mechanical installation ............................................................................................................ 13

3.1 Installation environment ................................................................................................... 13

3.2 Installing the drive ............................................................................................................ 13

3.3 Disassembling/assembling the junction box of drive ......................................................... 14

3.4 Installing the motor .......................................................................................................... 15

4 Electrical connection ............................................................................................................... 17

4.1 Wiring precautions ........................................................................................................... 17

4.2 Switch, contactor, and cable selection .............................................................................. 18

4.3 Terminal layout................................................................................................................. 19

4.4 Standard wiring ................................................................................................................ 20

4.5 Jumper function ............................................................................................................... 21

4.6 Wiring of main circuit ........................................................................................................ 22

4.6.1 Main circuit terminals ............................................................................................. 22

4.6.2 Resolver signal connectors (CN2A and CN2B) ....................................................... 24

4.6.3 Motor power cable and temperature measuring resistor terminals .......................... 24

4.6.4 Motor resolver connection cable and terminals ....................................................... 25

4.6.5 Typical wiring examples of main circuit ................................................................... 26

4.6.6 Wiring procedure for main circuit terminal CN6 ....................................................... 27

4.7 Input and output signal wiring ........................................................................................... 27

4.7.1 Input and output signal connector (CN5) ................................................................ 27

4.7.2 I/O output signal connector (CN1A) ........................................................................ 29

4.7.3 Typical control signal wiring examples .................................................................... 30

4.8 CAN/RS485 connector terminal (CN3) ............................................................................. 30

Summary of Contents for MH860 Series






























































































































Search results

Summary of Contents for MH860 Series

Reviews:

Related manuals for MH860 Series

Brands by name

Popular brands

INVT MH860 Series, Operation Manual

Search results

Summary of Contents for MH860 Series

Reviews:

Related manuals for MH860 Series

Brands by name

Popular brands