INVT MH860 Series Operation Manual Download Page 2 | Manualshive

Page: 2 / 125

background image

MH860 series hydraulic servo drive

Preface

i

Preface

Thank you for choosing MH860 series hydraulic servo drive developed by INVT Industrial
Technology Co., Ltd. If not otherwise specialized, the drive indicates MH860 series hydraulic
servo drive in the manual.

Designed for hydraulic equipment such as injection molding machine, die-casting machine,
and hydraulic press, the drive features energy saving, high accuracy, high efficiency and
durability for adopting high performance vector control. The drive has rich external expansion
and CAN communication interfaces, helping to form a multi-pump parallel system to realize
the hydraulic control on large flow equipment.

If you use the drive for the first time, please read this manual carefully to ensure correct and
safe operation. Please keep this manual in a safe place so that it can be consulted at any
time.

We are committed to the continuous product improvement and upgrade. The background
software and product information will be updated accordingly. Please download the latest
software and electronic document versions from our website www.invt-tech.com.

The target audiences of the manual include:



Control system designer



Installation or wiring personnel



User or maintenance personnel

Please make sure to observe the following:



The installation environment must be free of water vapor, corrosive gases, or
combustible gases.



Do not connect the grid power directly to the U, V and W terminals of the motor when
wiring. Otherwise, incorrect connection will cause drive or motor damage.



Ground wires must be grounded safely.



Do not disassemble the drive, motor, oil pump, or change the wiring while the power is
on.



Do not touch the heat sink at work to avoid burns.

We provide all-round after-sales and maintenance services. Do not disassemble the drive or
motor housing unless authorized; any modification on the drive or motor or damage
accompanied will revoke the warranty rights; and we will not be liable or responsible for the
consequences caused.

If you have any questions during use, please consult the dealer or our customer service
center.

«
1
2
3
4
...
»

Summary of Contents for MH860 Series






























































































































Reviews:

No comments

Related manuals for MH860 Series

Brand: Becker Pages: 20

Brand: Becker Pages: 20

Brand: Becker Pages: 28

Brand: Becker Pages: 52

Brand: Robotis Pages: 22

Brand: StepperOnline Pages: 12

Brand: FOTEK Pages: 171

Brand: LS Pages: 15

Brand: HPI Racing Pages: 2

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 118

VLT 2800 Series

Brand: Danfoss Pages: 103

Brand: YASKAWA Pages: 35

Brand: Baoding Longer Precision Pump Pages: 18

AlphaStep AZ Series

Brand: Oriental motor Pages: 120

Brand: Danfoss Pages: 46

TVD3.2 bl Series

Brand: Unitek Pages: 40

Brand: Eaton Pages: 203

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands