background image

3

Rev 05

Introduction

This manual describes the safety precautions, features, use and care, of the Invivo
HNC-63-INT Neurovascular Array Coil, compatible with the Philips Intera 1.5T MRI
System. Please review this manual thoroughly before using the device.

If you have any questions or comments on this manual, or need any assistance with the
use of the product, please contact your Invivo sales representative:

1-800-524-1476

Compatibility

The 

Invivo HNC-63-INT Neurovascular Array Coil

 is compatible with Philips Intera

1.5T MRI systems operating with Release 8.1.1 software or above.

NOTE:

 

Release 8.1.1 software requires a SYNERGY MULTICONNECT patch

available through Philips Medical Systems. Contact your Philips
Representative for this software patch. Software releases after 8.1.1 do not
require the software patch.

A SYNERGY MULTICONNECT device is required for use of this product.
Contact your Philips Representative for the Synergy MultiConnect device.

Manufacturer:

Invivo Corporation
3545 SW 47th Avenue
Gainesville, FL 32608
U.S.A.

Phone: (352) 336-0010
Fax:

(352) 336-1410

Web:

www.invivocorp.com

E-mail: [email protected]

For Sales and Service
in  Europe:

Invivo Germany GmbH
Schweinfurter Strasse 28
97076, Würzburg
Germany

Phone: +49 (0)931 359 76-0
Fax:

+49 (0)931 359 76-10

Authorized Representative in Europe:

GBM  Authorised Representative Ltd.
The White House, 2 Meadrow
Godalming, Surrey  GU7 3HN
United Kingdom

Phone: 44 (0) 7710 039721
Fax:

44 1483 424 310

Web:

www.mba-gbm.com

E-mail: [email protected]

Summary of Contents for Invivo 500082




























Reviews: