Optidrive E2 Single Phase Output User Guide V3.10
www.invertekdrives.com
24
A
n
alog and
Di
gita
l In
p
u
t Co
n
fig
u
ra
tion
s
7
Terminal Mode P-12=0, P-15=3
Terminal Mode P-12=0, P-15=4
Terminal Mode P-12=0, P-15=11
+24 Volt
+24 Volt
+24 Volt
Run (Enable)
Run (Enable)
Run Forward
Analog / Preset 1
Local / Remote
(Hand / Auto)
Stop
External Trip
Remote (Auto)
Reference
Fast Stop
+ 10 Volts
+ 10 Volts
Reference
Local (Hand)
Reference
0 Volts
0 Volts
Analog speed input with 1 preset speed and
motor thermistor trip
Local or remote analog speeds
(2 analog inputs)
Push button fwd/stop/fast stop using 2
nd
deceleration ramp
7.2.
Keypad Mode (P-12 = 1 or 2)
P-15
Digital input 1 (T2)
Digital input 2 (T3)
Digital input 3 (T4)
Analog input (T6)
Comments
0..2
5,
8..12
Open: Stop (disable)
Closed: Run (enable)
Closed : remote UP push-
button
Closed : remote DOWN
push-button
Open : Keypad speed ref
+24V : Preset speed 1
3
Open: Stop (disable)
Closed: Run (enable)
Closed : remote UP push-
button
External trip input :
Open: Trip, Closed: Run
Closed : remote DOWN
push-button
Connect external motor
thermistor PTC type or
similar to digital input 3
4
Open: Stop (disable)
Closed: Run (enable)
Closed : remote UP push-
button
Open : Keypad speed ref
Closed : Analog input 1
Analog input 1
6
Open: Stop (disable)
Closed: Run (enable)
No Effect
External trip input :
Open: Trip, Closed: Run
Open : Keypad speed ref
+24V : Preset speed 1
Connect external motor
thermistor PTC type or
similar to digital input 3
7
Open: Forward Stop
Closed: Forward Run
Open: Run
Closed: Fast Stop
External trip input :
Open: Trip, Closed: Run
Open : Keypad speed ref
+24V : Preset speed 1
Close digital input 3 to carry
out a fast stop (P-24),
provided P-05=0
Example Wiring
Keypad Mode P-12=1 or 2, P-15=0
+24 Volt
Run (Enable)
Increase Speed
Reduce Speed
Remote push button speed control
NOTE
By default if the enable signal is present the drive will not Enable until the START button is pressed. To automatically enable the drive when the
enable signal is present set P-31 = 2 or 3. This then disables the use of the START & STOP buttons
7.3.
Modbus Control Mode (P-12 = 3 or 4)
P-15 Digital input 1 (T2)
Digital input 2 (T3)
Digital input 3 (T4)
Analog input (T6)
Comments
0..2,
4..5,
8..12
Open: Stop (disable)
Closed: Run (enable)
No effect
No effect
No effect
Run and stop commands
given via the RS485 link and
Digital input 1 must be closed
for the drive to run.
3
Open: Stop (disable)
Closed: Run (enable)
Open : Master speed ref
Closed : Preset speed 1
External trip input :
Open: Trip, Closed: Run
No effect
Connect external motor
thermistor PTC type or
similar to digital input 3
6
Open: Stop (disable)
Closed: Run (enable)
Open : Master speed ref
Closed : Analog input
External trip input :
Open: Trip, Closed: Run
Analog input reference
Master Speed Ref - start and
stop controlled via RS485.
Keypad Speed Ref - drive
auto runs if digital input 1
closed, depending on P-31
setting
7
Open: Stop (disable)
Closed: Run (enable)
Open : Master speed ref
Closed : keypad speed ref
External trip input :
Open: Trip, Closed: Run
No effect
Further information the MODBUS RTU Register Map information and communication setup; please contact your Invertek Drives
Sales Partner.
