◄
Pagina 17
►
Step 6: Connect drain hose
The drainpipe is used to drain water away from
the unit. Improper installation may cause unit
and property damage.
NOTE ON PURCHASING PIPES
Installation requires a polyethylene tube
(exterior diameter = 3.7-3.9cm, interior
diameter = 3.2cm), which can be obtained at
your localhardware store or dealer.
1.
2.
Drainpipe
connecting port
Drain hose
Pipe clasp
Insulation
Cover the drainpipe with heat insulation to
prevent condensation and leakage.
Attach the mouth of the drain hose to the
unit’s outlet pipe. Sheath the mouth of the
hose and clip it firmly with a pipe clasp.
Lean over 1/100
•
Insulate all piping to prevent condensation,
which could lead to water damage.
•
If the drainpipe is bent or installed
incorrectly, water may leak and cause a
water-level switch malfunction.
•
In HEAT mode, the outdoor unit will
discharge water. Ensure that the drain hose
is placed in an appropriate area to avoid
water damage and slippage.
•
DO NOT
pull the drainpipe forcefully. This
could disconnect it.
CAUTION
NOTE ON DRAINPIPE INSTALLATION
•
When using an extended drainpipe, tighten
the indoor connection with an additional
protection tube. This prevents it from
pulling loose.
•
The drainpipe should slope downward at a
gradient of at least 1/100 to prevent water
from flowing back into the air conditioner.
•
NOTE:
When connecting multiple drainpipes,
install the pipes as illustrated.
Incorrect installation could cause water to
flow back into the unit and flood.
≥
10cm
(4”)
In order to ensure smooth drainage, the height
difference between the wall outlet and the
hanging plate must be greater than 470mm.
Drainage pipe fixing requirements
When installing the drainage pipe (not provided ),
please fix it with a tie or rope.
470mm
Recommended opening location
of connecting pipe outlet
�
55
Pasul 6: Conectati furtunul de scurgere
Conducta de scurgere este folosita pentru elimin-
area apei din unitate. Instalarea incorecta a aces-
teia, poate duce la defectarea aparatului.
1. Izolati conducta cu banda izolanta, pentru a preve-
ni aparitia condensului si a scurgerilor.
2. Conectati conducta la portul de conectare al uni-
tatii. Izolati si strangeti cu o clema metalica.
ATENTIONARE
NOTA CU PRIVIRE LA ACHIZITIONAREA CON-
DUCTELOR
NOTE CU PRIVIRE LA INSTALAREA CONDUCTEI
DE SCURGERE
•
Izolati tubulatura pentru a preveni aparitia conden-
sului. Pericol de defectare a aparatului.
•
Daca conducta de scurgere este indoita sau instalata
incorect, pot aparea scurgeri de apa care pot cauza
defectiuni ale sistemului de scurgere.
•
In timpul functionarii in modul incalzire, unitatea
exterioara va elimina apa. Asigurati-va ca furtunul
de scurgere este montat corect, pentru a evita
scurgerea apei si inghetarea acesteia in locuri circu-
late.
•
NU TRAGETI de conducta de scurgere pentru a o
deconecta.
Pentru aceasta instalare, veti avea nevoie de conduc-
ta de polietilena, cu diametru exterior de 3.7-3.9cm
si diametru interior de 3.2cm. Aceste conducte pot fi
achizitionate de la orice magazin de specialitate.
•
Daca extindeti conducta de scurgere, securizati conexi-
unea la unitatea interioara cu un tub de protectie, pentru
a preveni desprinderea acesteia.
•
Conducta de scurgere trebuie indreptata in jos, in treapta
de cel putin 1/100 pentru a preveni scurgerea apei inapoi,
catre unitate.
•
Instalarea incorecta poate duce la scurgerea apei inapoi in
unitatea interioara, cauzand inundatii.
NOTA:
Cand conectati mai multe conducte de scurgere,
instalati conductele asa cum este ilustrat.
Pentru a asigura o scurgere lina, diferenta de inaltime
dintre priza de perete si placa de suspendare trebuie sa
fie mai mare de 470 mm.
Cerinte de fixare a conductelor de drenaj. Cand instalati
conducta de drenaj (nu este furnizata), va rugam sa o fixati
cu o franghie.
Locatia recomandata de
deschidere a iesirii tevii de conectare
Furtun de scurgere
Port de conect-
are a conductei
de scurgere
Clema
metalica
Izolatie