background image

21

INVACARE

®

 SPIN

x

2-4.

B

A

B

A

C

1b.

B

E

C

D

1a.

ANTI-TIP DEVICES

The anti-tip device is foldable and adjustable in both 
height and depth. Please pay special attention to the 
placement of the anti-tip device when in use. A sticker 
will warn you if the anti-tip device is not activated.

1. Mounting
 a. 

Insert the two shorter screws into the holes in 

the rear part of the chassis according to picture 1a. 
Place the two spacers (B) on the screws. Note that 
the curved surface should be towards the tube. Fit 
the anti-tip device on the screws and tighten.

 b.

 Remove the back screw and nut on the rear 

wheel attachment and discard them. Mount the 
longer screw (C)  through the rear wheel attach-
ment according to picture 1b. Put the shorter screw 
(A) into the hole in the rear part of the chassis. Place 
one spacer (B) on the shorter screw (A) Note that 
the curved surface should be towards the tube. Fit 
the anti-tip device and tighten the screws.

2. Adjusting height
 

To adjust the height press the two knobs (B) on 
each side of the housing and pull the tube (C) to 
desired set of holes. 

 

The knobs will lock the tube into position.

Do not use knobs (B) to fold or unfold  the 
anti-tip device.

3. Adjusting depth
 

To adjust the depth press knob (D) and pull the 
wheel tube out to desired depth. The knob will lock 
the tube into position.

The distance between the anti-tip wheel and 
the ground, and the distance between the anti-
tip wheel and rear wheel, should be approx. 
5 cm.

4. Folding
 

To swing the anti-tip device under the wheelchair, 
press the cap (E) downwards and then sideways. 

NOTE!

  A red warning sticker can now be seen. 

 

To activate the anti-tip device, just swing it back in 
place and it will lock into position automatically.

NOTE!

 When the anti-tip device is correctly activa 

 

 

ted the warning sticker will be hidden. 

Use your foot when folding the anti-tip device. If 
you do it by hand, there is an increased risk that 
you will trap your fingers between the anti-tip 
housing and the tube.

Never forget to fold down the anti-tip devices 
or the wheelchair may tip over.

Make sure the anti-tip device is 
securely locked before use.

For safety reasons we recommend the 
use of two anti-tip devices!

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for SpinX





































Reviews: