Invacare rea Bellis Assembly Instructions Manual Download | Manualshive

Page: 13 / 24

background image

13

REA BELLIS

A

1.

2.

1.

You adjust the trunk support attachment by

loosening screw (A) using a 4 mm Allen key. Adjust
to the position that you require and retighten
the screw.

2.

You can open the trunk support pad using the zip.

You can then adjust the trunk support by loosening
the two screws using a Phillips screwdriver and
moving the trunk support forwards or backwards.
Retighten the screws and close the zip.

Trunk supports

Tools: 4 mm Allen Key

Tools: screwdriver

«
...
11
12
13
14
15
...
»

Summary of Contents for rea Bellis

























Reviews:

No comments

Related manuals for rea Bellis

Brand: aidapt Pages: 2

Cobi Cruise Power

Brand: Cobi Rehab Pages: 16

Brand: Vicair Pages: 20

Airrex LT Self-propelled

Brand: CareCo Pages: 24

Brand: Permobil Pages: 33

Brand: MINOS Pages: 47

Brand: JANE Pages: 3

Brand: CAMOBIL Pages: 13

Brand: Levo Pages: 50

Brand: Vela Pages: 24

Brand: broda Pages: 2

Light Drive 2.1

Brand: BENOIT SYSTEMS Pages: 4

Brand: Handicare Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands