iNtRON Miracle-AutoXT Instructions For Use Manual Download Page 28

     

Instruction for Use

USER MANUAL

IBT-QMS-INT50104 (R00)

28/34

Problem

Possible caused and comments

Instrument does not turn on.

Ÿ

Make sure to connect power cable to the instrument.

Ÿ

Check whether the instrument is plugged at 110~240V power
outlet.

Ÿ

Contact local distributors or technical service team if problem
continues.

Instrument is leaned

Ÿ

Adjust Rubber Feet to horizontalize the instrument

The motor is not working after
switching on the instrument.

Ÿ

Check whether fixtures (Both inside and bottom side of the

instrument) are completely removed. (refers to the section
'Installation')

Ÿ

Confirm absence of any foreign substances on sensor.

Ÿ

Check that the front door has been closed.

Ÿ

Contact local distributors or technical service team.

Touchscreen doesn't display
anything after switching on
the power button.

In case of motor doesn't work,

Ÿ

Ensure that the power cord is plugged in.

Ÿ

Check the fuse connection next to the power cord.

Ÿ

Contact the local distributors or technical service team.

In case of motor works,

Ÿ

Touch LCD could be disconnected from the power or out of
order.

Ÿ

Contact local distributors or technical service team.

LED light doesn't switch on

Ÿ

Make sure to connect power cable to the instrument and turn on
the instrument.

Ÿ

Check whether the instrument is plugged at 110~240V power
outlet.

Ÿ

Contact local distributors or technical service team if problem

continues.

Touch screen is not working

Ÿ

Restart the instrument

Ÿ

Contact local distributors or technical service team if problem
continues.

Can't locate Plate and strip at
the right position

Ÿ

Check whether plate and strip are inserted at the right position.
Refer to 'Installation' for details.

Ÿ

Confirm absence of any foreign substances on Heating Tray and
strip holder.

Ÿ

Check whether the plate and strip are deformed or bent.
Deformed or bent plate and strip may cause malfunction of the
instrument.

Ÿ

Contact local distributors or technical service team if problem
continues.

Summary of Contents for Miracle-AutoXT



































Reviews: