background image

21 

 

Seat Removal

 

Pull up on the front of the seat and slide it towards the front of the vehicle. To 

install the seat, slide the seat into the rear of the seat base until the two metal 

studs attached to the front of the seat are aligned with the two rubber grommets 

attached to the front of the seat base. Push down firmly on the front of the seat 

until the studs are fully seated into the grommets. 

 

Tilt Steering 

 

 

Figure 16: Steering Column 

Your Intimidator is equipped with tilt steering that can be adjusted by pulling the 

tilt steering lever towards you, then lifting the steering wheel up or pressing it 

down. The tilt steering lever is located on the steering column, directly behind the 

steering wheel.  

 

Hauling Cargo 

 

Danger: 

Always follow these precautions when hauling cargo: 

  Refer to the cargo bed safety warning label, located in the cargo bed. 

  Driving with passengers in the cargo box can result in severe injury or 

death. Never allow passengers to ride in the cargo box. Passengers must 

always ride in the cab with seatbelts fastened securely. 

  Hauling cargo improperly can alter vehicle handling and may cause a loss 

of control which can result in serious injury or death. 

  Never exceed the maximum weight capacity of the vehicle. When 

determining the weight that you are adding to the vehicle, include the 

weight of the operator, passengers, accessories, cargo loads, and the load 

on the trailer tongue. The combined weight of these items must not exceed 

the maximum weight capacity. 

Summary of Contents for GC 1K











































































Reviews: