background image

15

Jøtul C 

550

 CB Rockland    139656_02     10/2/14

Operation

Read the following section carefully before building 

a fire in your fireplace insert..

Fuel

This stove is designed to burn natural wood ONLY. 

Wood that has been air-dried for a period of 6 to 14 

months will provide the cleanest, most efficient heat. 

Frequent use of green or inadequately seasoned 

wood is conducive to creosote accumulation and 

generally poor performance.

 

DO NOT BURN...

•Coal   

   •Treated or painted wood

•Garbage 

   •Chemical Chimney cleaners

•Cardboard 

   •Colored paper

•Solvents 

   •Any synthetic fuel or logs

The burning of any of these materials can result in 

the release of toxic fumes. 

NEVER USE GASOLINE, 

GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHAR-

COAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START 

OR “FRESHEN-UP” THE FIRE.  Always keep such liq-

uids away from the heater at all times.

Air Control Settings

A single lever regulates the Primary Air flow that 

controls the intensity of the fire and consequent heat 

output and burn time. This lever is located within the 

slot on the upper right front of the fireplace insert.

When first starting or reviving the fire, the 

control lever should be set at the far right position 

to allow the maximum amount of air into the stove.  

See fig.15. After the fire is well-established, the lever 

should be set at position to moderate incoming air to 

maintain the desired long term heat output and/or 

burn time. 

In general, the more air made available to the 

fuel will result in the hottest fire intensity and the 

fastest fuel consumption. Alternatively, the less air 

made available to the firebox will result in low heat 

output and slow fuel consumption.

               

Use the following guide for best performance.

Burn Rate     Air Control Setting     Blower Speed

 

Low 

 

5/32” Open 

Low / On at 30 min. 

Med. Low 

3/16”-5/16”Open  Low / On at 30 min. 

Med. High 

5/16”-1/2”Open  Low / On at 30 min. 

High 

 

Max. Open 

High / On

Blower Settings / Air Control             

  WARNING
NEVER ALLOW THE FIRE TO REST  

DIRECTLY ON THE GLASS.  THE 

LOGS SHOULD ALWAYS BE SPACED 

AT LEAST ONE INCH FROM THE 

GLASS TO ALLOW FOR PROPER AIR 

FLOW WITHIN THE STOVE.

OPERATE THIS FIREPLACE INSERT 

ONLY WITH THE FRONT DOOR FULLY 

CLOSED. OPERATION WITH A PAR-

TIALLY OPENED DOOR MAY RESULT 

IN OVER-FIRING.  ALSO, IF THE 

DOOR IS LEFT PARTLY OPEN, GAS 

AND FLAME MAY BE DRAWN OUT 

OF THE STOVE OPENING, CREAT-

ING RISKS FROM BOTH FIRE AND 

SMOKE.

Figure 15.  Air Control Setting

Control Lever

Summary of Contents for Jotul C 550 CB Rockland





























Reviews: