background image

International Gas Detectors Ltd            T: +44(0)161 483 1415

 

V1.0                  

            Email:

[email protected]

                          

 

               

- 13 - 

 

      

Fig. 18

 

7. Time set 
In the menu function interface, select the time, 
enter it as shown in the figure 18, press the "

" key to move the cursor, use the

▲▼

key 

to set the current system time, press the

key 

return to the main menu. 

4.5. Charging 

Please charge the detector when it shows low battery,  or the 
detector cannot be turned on due to low battery. Before charging, 
please turn off the detector. After you connect the charger correctly 
between the detector and AC power source, the detector will be 
turned on automatically. When the battery mark on the screen is full 
and  does not  change any more, it means the charging is 
completed. Disconnect when charging is complete.  

Warning: 

 

Please do not charge it when the detector is 
working to avoid potential damage.  

Note: Make sure full charge for at least once within 3 months 
since production date. 

 

5. Possible fault and corresponding solution

 

Possible fault  

Possible reason  

Corresponding solution  

The detector 

cannot be turned 

on 

Too low battery 

Please charge  

The sensor failure 

Please contact IGD 

Fault of electric circuit  Please contact IGD 

No response to 

the gas 

Warm up is not 

finished 

Wait till warm up is 

finished 

Fault of electric circuit  Please contact IGD 

Summary of Contents for POR-MULT


















Reviews: