manualshive.com logo in svg

International Biomedical AeroNOx, Operating Manual, Page: 13 / 64

Share
Download
International Biomedical AeroNOx Operating Manual Download Page 13

 

 

Document No.  715-7000

 

Revision E 

Page 12 of 63 

 

Do not substitute AeroNOx

 Bagger components!  The AeroNOx

 Bagger has been 

designed and tested for patient safety with the components included in the current 
configuration. 

 

 The 

AeroNOx

 Bagger is designed for use only with the AeroNOx

 Delivery System.  Do 

not attempt to use the AeroNOx

 with any other manual resuscitator.  Do not attempt to 

use the AeroNOx

 Bagger with any other delivery system. 

 

 

A backup system must always be available in the event that the primary system should 
fail.  For instructions for use of a Back-Up System in the event of a failure of the 
AeroNOx

 system, please see 

SECTION III

, Back-Up system. 

 

 The 

AeroNOx

 Bagger is intended to be connected directly to the patient’s endotracheal 

tube.  Do not insert any additional tubing between the AeroNOx

 Bagger and the 

endotracheal tube. 

 

 The 

AeroNOx

 Bagger is for single patient use only.  Do not reprocess. 

 

 

Persons using this device should be trained and experienced in the use of this device to 
assure affective administration of nitric oxide, and to avoid injury to the patient or to 
others resulting from inhalation of excess nitric oxide, nitrogen dioxide, or other reaction 
products. 

 

 

Persons using this device who may be particularly sensitive to nitric oxide, or who may be 
exposed to these gases for prolonged periods as a result of the use of this device, should 
be aware that the gases exiting the AeroNOx

 Bagger are not scavenged. 

 
1. 

Connect the large end of the bagger gas supply tubing to an oxygen source.  Ensure that 
the small end of this tubing is connected to the NO / O

2

 gas inlet port on the bagger. 

 
2. Connect 

AeroNOx

 Bagger gas delivery line to the AeroNOx

 delivery gas port. 

 
3. 

Connect male end of the sample line (P/N 415-0004) to the sampling port on the bagger 
gas supply tubing and the female end to the AeroNOx

 sampling port. 

 
4. Set 

O

2

 flow on the O

2

 flow meter to exactly 10 LPM.  Let the oxygen run for at least 20 

seconds to flush out any residual NO or NO

2

 left in the AeroNOx

 Bagger. 

 
5. 

Turn on NO delivery gas source to 0.25 LPM.  If you have correctly set your O

2

 flow at 

exactly 10 LPM, the delivered NO concentration will be ~20 ppm and delivered NO

2

 

values should not exceed 0.2 ppm.  

Do not exceed 20 ppm during manual ventilation! 

 
6. 

Connect test lung and set overflow valve to desired positive end expiratory pressure 
(PEEP). 

 

Summary of Contents for AeroNOx

































































Reviews:

No comments