• To delete a holiday# (and thus its Start/Stop dates) that has
never had any scheduled On/Off times: Press
SET UP
, then
HLDY
, then the Holiday #, then
REV
, then
CLEAR
. If the
display shows "__", the Holiday has been deleted. If "ERR 22"
shows, this Holiday has, or once had, a schedule. If so, press any
key to clear the error message then follow the steps below.
• To delete a holiday# (and thus its Start/Stop dates) when the
holiday has or once had scheduled On/Off times: Enable any
circuit, press
PROG
, then
HLDY
, then the Holiday #, then
REV
. The selected Holiday # will show. Press
CLEAR
; the timer
will scroll a message asking if you are sure you want to delete the
Holiday schedule. After the message stops and the Holiday # is
re-displayed, press
CLEAR
to delete it. Now press
SET UP
, then
HLDY
, then the Holiday #, then
REV
, then
CLEAR
. The
holiday is now completely deleted.
PROGRAMMING EXAMPLE
(
2 circuits only
)
Be sure
RUN/SET
is in
SET
position. At the initial installation
and/or to clear out all previously programmed data, press and hold
the
CLEAR
button, then press and release
RESET
and continue to
hold the
CLEAR
button until
RESET
appears in the display
.
Note
leading zeros are not required for the left-most prompted digit.
Press
SET UP
(unless prompt is flashing at
Day of Wk/Time
)
Assume
• Current day and time is Tuesday, 2:30 P.M.
• Current date is January 21, 1997
• Location is Des Moines, Iowa (Zone 5 from Astro
Zone Map and center of Central time zone)
• The building owner wants the lights Off 30 min.
after sunrise and On 30 min. prior to sunset.
• Two Holiday or special schedules – July 4th and a
2-week office closing 12/22/97 thru 1/5/98
Press
TUE/3, OK
(selects day);
2, 3, 0, PM, OK
(selects time);
1, 2, 1, 9, 7, OK
(selects date);
5, OK
(selects zone).
The time switch now displays the calculated center of
time zone sunrise time of -7:33 A.M. Since the building
17
Next Generation
review. You must revise the data by reviewing the appropriate
individual day, day group, or "copied from" day.
• During automatic review, the
OK
key must be used to pause
the display before the displayed data can be deleted.
• After any program data is cleared, review is terminated. The
timer is now in the program mode for the selected day,
anticipating a new entry. You may make the new entry, restart
review, or return to RUN position.
• It is recommended that you repeat the "week long review" after
any revisions are complete to verify that all revisions were
implemented as desired.
To revise or delete displayed information during Program Review,
simply press
CLEAR
. You can then immediately make the revision
desired. Be sure to press
OK
to enter the new data. Press
REV
to
restart the review. Note that you can delete a Pulse or Interval
option from any Switch On or Switch Off time by pressing
CLEAR
when the time is displayed during Review. You must re-
enter, then
OK
the Switch On or Switch Off time, even if it has
not changed. Likewise, you may add a Pulse or Interval to a
Switch On or Switch Off time by pressing
CLEAR
when the time
is displayed. You must re-enter the time, press
PULSE
or
INTVL
,
enter the length of Pulse or Interval, then press
OK
.
REVISE/DELETE HOLIDAY SCHEDULES AND
DATES
• To revise holiday Start/Stop dates: Press
SET UP
, then
HLDY
,
then the Holiday # (if known), then
REV
. The selected Holiday
# will show. Press
REV
again; the
START
date will show.
Pressing
CLEAR
will delete the
START
and
STOP
dates. Enter
the new START date, then
OK
. Enter the new STOP date, then
OK
.
• To revise holiday schedules: Press
PROG
, then
HLDY
, then the
Holiday #. Press
REV
until the time that requires revision is
displayed. Press
CLEAR
to delete the displayed time. Enter and
OK
a new time if desired.
16
