3
2.
Press Arm Doors & Windows button.
3.
Enter Access Code (if needed).
Panel announces any protected doors or windows that are
open. Any sensors that are open when the system is armed
will be bypassed after exit. Arm Doors & Windows light
will be lit and the exit delay will begin.
Note
Any sensors that are bypassed by the system will
NOT be protecting your home.
Arming Your System with No Entry Delay
Note
No Entry Delay can be used in two ways. You can
use this feature when you’re staying at home, after
you’ve armed the system (i.e. when you’re asleep).
Second, you can use this when you’re away from
your home. To avoid causing an alarm, you must dis-
arm the system with a remote handheld touchpad or
keychain before entering your home. Check with
your installer to find out how this option is pro-
grammed.
1.
Close all doors and windows.
2.
Press Arm Doors & Windows button twice.
3.
Enter Access Code (if needed).
Panel announces, Doors and windows on, no entry delay.
Arm Doors & Windows light will blink and the exit delay
will begin.
Arm Motion Sensors
1.
Press Arm Motion Sensors button once.
2.
Enter access code (if needed).
Panel announces, Motions on. Arm Motion Sensors light
will be lit and the exit delay will begin.
Note
This feature is most likely used when there is no one
on the premises.
Activate Latchkey Feature
1.
Press the Arm Motion Sensors button twice.
2.
Enter Access Code (if needed).
Panel announces, Motions on, Latchkey on. Arm Motion
Sensors light will blink and the exit delay will begin.
Disarming Your System
1.
Upon reentering your home the entry delay will begin.
2.
Status beeps will sound.
3.
Enter your access code using the Code buttons.
Panel announces, System disarmed and the Disarm light
will be lit.
WARNING!
If you enter your home and you hear alarm sirens, or
if controlled lights that should be off are on, an
intruder may be inside or another emergency may
have occurred. Leave immediately and call for help.
Subdisarm Your System
1.
Enter your Master Access Code while the system is
disarmed.
Panel announces, System disarmed. Disarm button light
blinks and the system is subdisarmed. When you’ve fin-
ished accessing the protected areas, press the Disarm but-
ton again. Panel announces, System disarmed. Disarm
button light stops blinking. System is in Disarm mode.
If You Never Leave After Arming
Your panel can be programmed to recognize that you
never left the premises. If you press the Arm Doors &
Windows button and the Arm Motion Sensors button but
don’t exit before the exit delay expires, the panel will not
arm the motion sensors. Check with your installer to find
out if this feature is enabled for your panel.
If You Forgot Something After Arming
Your panel can be programmed to recognize when you
leave the premises then quickly reenter. The panel will
restart the exit delay to give you time to collect your things
and leave again. You must leave before the exit delay
expires or disarm the system. Ask your installer if this fea-
ture is enabled for your system.
Arming When the Panel Battery is Low
Your panel may be programmed so that you cannot arm
the system if the panel battery is low. Ask your installer.
CODE
There are 5 CODE buttons located in the second row of
the panel. Each button represents 2 numbers. The left
CODE button is 1/2, which means that this button is
pressed when entering either 1 or 2. For example, if your
access code is 1-2-3-4 you must press the 1/2 button twice
and the 3/4 button twice to enter that access code. Access
code lengths need to be between 3 and 6 digits.
C O D E
9 / 0
5 / 6
7 / 8
1 / 2
3 / 4
Summary of Contents for Simon 3
Page 19: ...17 ...
