18 / 42
P/N 466-
2523 (ML) • REV D • ISS 16JUN17
Nouveau PIN
>_
Entrer le nouveau code PIN
installateur et appuyer sur Entrer
Vérifier
>_
Ensuite, entrer de nouveau le code
PIN pour le vérifier.
Changer PIN
Superviseur
Appuyer sur Entrer pour continuer
Nouveau PIN
>_
Entrer le nouveau code PIN
superviseur et appuyer sur Entrer
Vérifier
>_
Ensuite, entrer de nouveau le code
PIN pour le vérifier.
La centrale redémarre.
Configuration automatique
Config Auto ?
>Oui<
Appuyez sur Enter pour continuer.
RAS 1-16 BUS1
R-?-------------
DGP 1-15 BUS1
-?-------------
Aud 1-16 BUS1
---?------------
Attendez que la centrale ait configuré
l'ensemble des zones et modules bus.
Ajouté
R:1 D:0 Z:8
A:0
Appuyez sur Enter pour continuer.
Activer le mode de maintenance
UTC F&S
JEU 5 Mar 12 h 21
Entrer le code PIN Superviseur et
appuyer sur Menu.
1>Options zone
2 Isoler
Rendez-vous dans le menu 8.8 Mode
de maintenance
8>Maintenance
Activer ?
Activez la fonction Service, rendez-vous
Appuyez sur Annuler, Annuler pour vous déconnecter.
Programmation de l'entrée de menu
UTC F&S
JEU 5 Mars, 12h21
Entrer le code PIN Installateur et
appuyer sur Menu
Excl rapports
>Non<
Appuyez sur Enter pour continuer.
Excl autoprot
Désarm groupes
1>Maintenance
2 Modules BUS
Le menu Installateur s'affiche.
Modification de la clé de cryptage
Attention :
il est fortement recommandé de modifier la clé de
cryptage par défaut.
Consultez les sections
9.4.3 Clé de cryptage 1 et 9.4.4 Clé de
cryptage 2.
3 Clé cryptage 1
>000000000000<
Ajoutez la clé de cryptage 1.
4 Clé cryptage 2
>000000000000<
Ajoutez la clé de cryptage 2.
Configuration des zones
Consultez la section « 4.1 Menu de zone ».
4>Zones&Groupes
Appuyez sur Enter.
1>Zones
Appuyez sur Enter.
0>Ajouter zone
1 Zone 1
Sélectionnez une zone.
Dans la section « 4.1.n.1 Nom de la zone », spécifiez le nom
de chaque zone
utilisée dans le système.
01 Nom zone
>Zone 1 <
Définissez ensuite le type de zone dans la section « 4.1.n.2
Type de zone
».
02 Type de zone
>E/S 1<
Ajout d'utilisateurs
Accédez à la section « 3.1 Utilisateurs ».
0>Ajouter util
1 Installateur
Appuyez sur Enter pour ajouter un
utilisateur.
Ajouter mode
>Manuel<
Appuyez sur Enter.
INFO
Util ajouté
01>Nom util.
Utilisateur 3
Appuyez sur Enter.
01 Nom util.
>Utilisateur 3 <
Saisissez un nouveau nom
d'utilisateur.
Configurez les autres options liées à l'utilisateur.
•
« 3.1.n.2 Code PIN »
•
« 3.1.n.3 Carte utilisateur »
•
« 3.1.n.6 Groupe util », etc.
Procédez de la même manière avec chaque utilisateur.
Une fois un utilisateur configuré, verrouillez ses données.
Verr don ut ?
>Annuler<
Choisissez OK, puis confirmez.
Configuration des groupes
Accédez à la section « 4.2 Groupes ».
Dans « 4.2.n.1 Nom du groupe », modifiez le nom du groupe.
01 Nom du groupe
>Groupe 1 <
Saisissez un nouveau nom de groupe.