15
Allegro
Preliminary 2/5/02
Siren (1st Tier)
Exit - DL (1st Tier)
If Exit is selected, the panel returns to active mode. If the
installer/dealer code is entered, a downloader session will
begin.
After all installer programming is completed, use the fol-
lowing procedure to exit programming mode.
To exit programming mode:
Press * until
EXIT
-
DL
is displayed
and then press #. The
current time will be displayed.
Or
Press * until
EXIT
-
DL
is displayed
and then enter
installer or dealer code to start a Downloader session.
User Programing Menu Items
This section guides you through the user programing menu
items as they appear in sequence.
Entering User Programming Mode
There are two tiers of user programming menus. Tier 1
menus are accessible immediately after entering the pro-
gram mode.
Figure 11. Tier 1 User Programming Menus
Arrows pointing left and right represent the up and down
arrows on the panel.
You can enter the user programming mode using the pri-
mary access code. The default primary access code is
1234
.
To enter user programming mode:
With the system disarmed, press
8
+
CODE
. This will
take you to
CODES
,
the first menu item in Tier 1.
Codes (1st Tier)
Auto Phone Test
(Reports)
2nd Tier
(Default = off) This setting determines if the panel sends a
phone test automatically to the central station at Supervisory
Time. Refer to the “Phone Test Frequency” and “Next Phone
Test” on page 11.
Note
For UL Listed installations, the Auto Phone Test feature
must be set to on.
To turn automatic phone test on or off:
Press # to turn on or off.
Siren Time Out
(Siren)
2nd Tier
(Default = 4 minutes, Parameters = 1-30) Siren Time-out
determines how long sirens sound if no one is present to
disarm the system.
Note
For UL Listed installations, the Siren Time-out must be set
to 4 minutes or more.
To set siren time out:
1. Press
#, enter the desired time and then press #.
Trouble Beeps
(Siren)
2nd Tier
(Default = on) When this setting is on, the panel will beep to
alert users of system trouble.
Note
For UL Listed installations, Trouble Beeps must be set to
on.
To turn trouble beeps on or off:
Press # to turn on or off.
Alarm Volume
(Siren)
2nd Tier
(Default = 6, Parameters = 0 to 6) This setting allows you to
adjust the panel’s siren volume. The volume can be set from 0
to 6, with 0 being the lowest volume.
Note
Alarm Volume must be set to 6 for UL installations.
To set the alarm volume:
1.
Press #, enter the desired volume level and then press #.
Apartment Manager
(Codes)
2nd Tier
(Default = none, Parameters = 4 digits, 0 to 9) The apartment
manager code functions the same as the primary code within
the user programming menu, and can arm or disarm the
system.
Note
This code will only be displayed in user programming if the
apartment manager code was used to enter user program
mode.
To program/change apartment manager code:
1. Enter the apartment manager code. The display shows
CODES
.
2. Press
#. The display shows
MANAGER
.
3. Press
# to display the current code (if any).
4. Press
#, enter the desired code and then press #.
Primary
(Codes)
2nd Tier
(Default = 1234, Parameters = 4 digits, 0 to 9) The primary
code performs all system operations and user programming.
To set the primary code:
1. Press
# to display the current code.
2. Press
#, enter the desired code and then press #.
S e n s o r
T e s t
V o l u m e
E x i t
T i m e
C o d e s
T i e r 1 M e n u
V e r s i o n
P h o n e
T e s t
