Interlogix ADC-IS-300-LP Installation Manual Download Page 1 | Manualshive

Page: 1 / 15

background image

Interlogix Simon XTi Image Sensor Installation Guide - ADC-IS-300-LP

PRODUCT SUMMARY & TECHNICAL SPECIFICATIONS

The Image Sensor is a pet immune PIR (passive infrared) motion detector with a built-in camera designed to capture
images during alarm or non-alarm events when motion is detected.

Product Features:

• Communicates wirelessly to the security control panel

• 35 foot detection range with a 90 degree horizontal FOV

• Configurable PIR sensitivity and pet immunity settings

• Image: VGA 640x480 pixels

• Color Images (except in night vision)

• Night vision image capture with infrared flash (black & white)

• Tamper detection, walk test mode, supervision

• All systems can support up to three Image Sensors

• UL 639 certified

Technical Specifications:

• Alarm.com Model Number: ADC-IS-300-LP

• Interlogix Part Numbers:

• Power Source: Recommended 2 AA 1.5v Energizer Ultimate Lithium Batteries.

• Batteries: Refer to the Batteries section for details

https://answers.alarm.com/Installation_and_Troubleshooting/Image_Sensor/Interlogix_Simon_XTi_Image_Sensor/Interlogix_Simon_XTi_Image_Sensor_Installation_Guide_-_ADC-IS-300-LP

Updated: Tue, 17 Apr 2018 13:48:15 GMT

1

1
2
3
...
»

Summary of Contents for ADC-IS-300-LP
















Reviews:

No comments

Related manuals for ADC-IS-300-LP

Brand: Klarstein Pages: 96

Brand: PASCO Pages: 6

Brand: PASCO Pages: 4

CK 3000 Evolution

Brand: Parrot Pages: 2

Brand: Labona Pages: 12

Brand: iArmor Pages: 6

Brand: hepco & becker Pages: 4

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

SPEEDLOADER BRIDGE SYSTEM

Brand: Floyd Rose Pages: 10

Brand: Ledvance Pages: 6

Brand: VDO Pages: 236

Brand: Kambrook Pages: 12

Brand: Raw Thrills Pages: 49

Brand: Ultrak Pages: 16

EVOLUTION PACK FOR NDS LITE

Brand: GAMERON Pages: 24

SEMIFARINGS ANARCHY

Brand: CUSTOMACCES Pages: 2

BELL SYSTEM FG-16 V3

Brand: M-E Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands