![background image](http://html.mh-extra.com/html/interlogix/adc-is-300-lp/adc-is-300-lp_installation-manual_2076681008.webp)
Simon XTi/XTi-5
1. Put the panel into add mode. On the panel, scroll until the screen shows “Programming” > Enter installer code
(default 4-3-2-1) > Select “Interactive Services” > Select “Image Sensor” > Select “Add” > The screen will display
“Reset or power-up sensor to enroll…”
2. Insert the batteries into the Image Sensor. The LED on the Image Sensor will progress from blinking red to solid
red to blinking yellow. This indicates the Image Sensor is in learn mode.
3. Wait approximately 20 seconds for the Image Sensor to enroll to the panel. The screen on the panel will display
the following: “I.S. [x] Added as Sensor [y].” The LED on the Image Sensor will turn solid yellow indicating that it
has successfully found the panel.
4. After the Image Sensor LED has turned solid yellow, you must exit Add Mode on the panel. The Image Sensor
LED will alternate between green and yellow while the customer’s device list is updated with Alarm.com. The LED
will turn solid green when the Image Sensor has been successfully added to the customer’s account. Note: If you
move (tamper) the Image Sensor after the LED has turned solid green, the Image Sensor will enter test mode for 3
minutes indicated by red LED when motion is detected. You may continue with the mounting portion of the
installation when in test mode. See the Image Sensor LED Reference Chart for more details.
The sensor is now learned into the panel. Sensors are enrolled in group 17 by default. To change the sensor group, use
the Sensors menu in Programming. Image Sensors may be enrolled in groups 15, 17, 20, or 25. (No chime issued for
group 25.) After enrollment, be sure to keep the sensor and panel powered so the sensor can complete an initialization
process with the Alarm.com Network Operations Center. This process will take several minutes. Images cannot be
captured until initialization is complete. Check by verifying if the rules are confirmed on the dealersite or MobileTech.
Concord
1. Install Image Sensor Daughterboard – See Daughterboard Install Guide for more details.
2. Connect Daughterboard Alarm Wire – See Daughterboard Install Guide for more details.
3. Register Module and Test - Power up the panel and initiate a comm-test to ensure the Alarm.com module is
properly installed and communicating with the Alarm.com NOC.
4. Press button on IS daughterboard to enter ‘Add Mode.’ The green LED “Z2” will start a 4-blink pattern indicating
that the daughterboard is in ‘Add Mode’.
5. Reset or insert the batteries into the image sensor. “Z2” LED on the daughterboard will be solid for 60 seconds to
indicate that the sensor has been added.
6. The LED on the Image Sensor will progress from blinking red to solid red to blinking yellow to solid yellow.
Note
: The Image Sensor WILL NOT show in the panel’s sensors menu as occupying a panel zone, but the zone
must be reserved for the Image Sensor. It is enrolled starting with zone 92 and counts down. The Alarm.com
Dealer Site equipment list will show the Image Senor in its enrolled zone. By default, the sensors are enrolled in
partition 1 and group 17. During step 6, the Image Sensors will be re-assigned to follow the partition and group of
the hardwire.
7. To begin enrolling Image Sensor Alarm Hardwire in panel - Enter sensor enrollment menu in System
Programming.
8. Select the partition number, zone number, and sensor group for the hardwire.
9. Trip daughterboard hardwire by pressing button on top of daughterboard. The red LED “Z1” on daughterboard will
turn off when pressed.
10. Exit system programming. The Image Sensors will now be assigned to the group and partition of the hardwire.
https://answers.alarm.com/Installation_and_Troubleshooting/Image_Sensor/Interlogix_Simon_XTi_Image_Sensor/Interlogix_Simon_XTi_Image_Sensor_Installation_Guide_-_ADC-IS-300-LP
Updated: Tue, 17 Apr 2018 13:48:15 GMT
8