Interfacion QED-PL2 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 35

background image

24

7: BATTERY

Description

Displays the battery range from ~5.98 - 9.99 Volts
The detector is designed to run on a battery voltage of 10 Volts
maximum and 6 Volts minimum.
To protect rechargeable batteries, the detector will automatically turn
off when the battery voltage is below 6 Volts.

Note: When the battery is nearly flat a decimal point appears on the screen. If

the operator shuts down when the decimal point appears then current
settings will be saved.

Note: If the detector shuts off due to low battery then current settings will NOT

be automatically saved.

Further, the REMOTE SPEAKER if fitted, needs to be turned ON/ OFF
independently. The speaker contains 3/AAA batteries that can be
replaced after carefully separating the speaker body and speaker
base.

Lithium (li ion) Battery Care

Click on the following link to view an article explaining the safe storage
of lithium (Li Ion) batteries:

https://batterybro.com/blogs/18650-wholesale-battery-reviews/77975750-how-to-
store-18650-batteries-safely

Notes

«
...
22
23
24
25
26
...
»

Summary of Contents for QED-PL2




































Reviews:

No comments

Related manuals for QED-PL2

Brand: DALEMANS Pages: 16

Brand: Detech Pages: 22

Brand: C-SCOPE Pages: 13

Brand: Barska Pages: 12

MX400 Stryker Lite

Brand: GroundEFX Pages: 23

Brand: K40 Pages: 2

Brand: GSSI Pages: 68

Brand: Whites Pages: 56

Brand: Xplore Pages: 24

Brand: makro Pages: 30

Brand: ZKTeco Pages: 33

Brand: Accurate Locators Pages: 67

Brand: WatchGas Pages: 4

Brand: BallistiGlass Pages: 3

Brand: Mircom Pages: 2

Brand: Dräger Pages: 4

Brand: Vivax Metrotech Pages: 5

Everywhereyoulook GD10-P00

Brand: TELEDYNE OLDHAM SIMTRONICS Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands